最新なJuniper JN0-364問題集（180題）、真実試験の問題を全部にカバー！

質問 1：
Click the Exhibit button.

You have configured an MPLS LSP that begins on R1 and terminates on R5 using the Junos default settings.
Referring to the exhibit, which router will perform only label swap operations?
A. R5
B. R1
C. R3
D. R4
正解：C
解説: (Pass4Test メンバーにのみ表示されます)

質問 2：
Referring to the exhibit. You configured interface ge-0/070.0 to run IS-IS. but this interface does not appear in the output of the show isis adjacency command as shown in the exhibit.
What is the problem in this scenario?

A. This is a Gigabit Ethernet interface, that is incompatible with the reference-bandwidth 100g statement.
B. The family iso statement must be added to the logical interface.
C. The router at the other end of the link is a Level 1 only router.
D. The router at the other end of the link Is not sending any IS-IS Hello messages.
正解：B
解説: (Pass4Test メンバーにのみ表示されます)

質問 3：
An established RSVP-signaled LSP suffers a link failure. What is one action taken by the local RSVP-enabled router?
A. A ResvErr message is sent upstream.
B. A ResvTear message is sent downstream.
C. A ResvErr message is sent downstream.
D. A ResvTear message is sent upstream.
正解：D

質問 4：
You are deploying an MC-LAG connection at the edge of your network to a new customer. This solution must ensure that traffic uses all available links when forwarding traffic between the two networks.
In this scenario, which two statements are correct? (Choose two.)
A. You must use active/active mode when defining the MC-LAG bundle.
B. Transit traffic sent between the two PE devices will use the ICL interface.
C. You must use active/standby mode when defining the MC-LAG bundle.
D. Transit traffic sent between the two PE devices will use the bundle's member interfaces.
正解：A,B

質問 5：
Which statement is correct about the FE80::/10 prefix?
A. This prefix range is used for the link local address.
B. This prefix range is not reserved.
C. This prefix range is reserved for multicast applications
D. This prefix range is used on the loopback interface.
正解：A
解説: (Pass4Test メンバーにのみ表示されます)

質問 6：
Referring to the exhibit. You are asked to assign interface xe-1/0/5 to a virtual switch. What must be accomplished to complete the configuration?

A. Interface xe-1/0/5 must be added to routing-instance sw-1.
B. Interface xe-1/0/5 must be added to routing-instance sw-1 vlan_2.
C. Interface xe-1/0/5 must be a trunk port.
D. An IRB interface must be configured to routing-instance sw-1 vlan_2.
正解：B
解説: (Pass4Test メンバーにのみ表示されます)

質問 7：
Referring to the exhibit, you have an established RSVP LSP between R1 and R4 when you experience a link failure between R2 and R3.
Which two statements are correct? (Choose two.)

A. R3 sends a ResvTear message downstream to R4 signaling the link failure.
B. R2 sends a PathTear message upstream to R1 signaling the link failure.
C. R3 sends a PathTear message downstream to R4 signaling the link failure.
D. R2 sends a ResvTear message upstream to R1 signaling the link failure.
正解：A,D
解説: (Pass4Test メンバーにのみ表示されます)

質問 8：
You must ensure that your routing platform with redundant REs continues to forward packets, even if one RE fails.
Which technology would you use to accomplish this task?
A. NSB
B. GRES
C. BFD
D. LAG
正解：B
解説: (Pass4Test メンバーにのみ表示されます)

質問 9：
When considering BGP route propagation, which two statements are correct? (Choose two.)
A. IBGP speakers send routes learned from EBGP neighbors to IBGP neighbors.
B. EBGP speakers send routes learned from IBGP neighbors to IBGP neighbors.
C. IBGP speakers send routes learned from IBGP neighbors to IBGP neighbors.
D. EBGP speakers send routes learned from EBGP neighbors to IBGP neighbors.
正解：A,B