最新なH3C GB0-381-ENU問題集（522題）、真実試験の問題を全部にカバー！

質問 1：
Which of the following statements is true regarding the comparison between OSPF and RIP?
A. OSPF is less secure than RIP
B. The network with OSPF is more scalable than the network with RIP
C. OSPF is more reliable than RIP
D. OSPF converges faster than RIP
正解：B,C,D

質問 2：
In the topology shown in the figure, the following configurations are performed on RTA , RTB , RTC and RTD respectively

then no injection into zone 2
A. Type3 LSA
B. Type5 LSA
C. Type7LSA
D. Type4 LSA
正解：A,B,D

質問 3：
Which of the following descriptions of Route-polic is incorrect __________?
A. In the same node of Route-polic, the relationship between different if-match clauses is and
B. In a Route-polic, the relationship between different nodes is or
C. In a node of the Route-polic, at least one if-match clause must be included
D. If more than one node is defined in the Route-polic, at least one of the nodes should have the matching mode permit
正解：C

質問 4：
In the topology shown in the figure, the following configurations are performed on the RTA and RTC respectively:
RTA-ospf-1] area 1
RTA-ospf-1-area-0.0.0.1] authentication-mode simple
RTA] interface GigabitEthernet0/0
RTA-GigabitEthernet0/0] ospf authentication-mode simple plain 12345
RTC-ospf-1] area 0
RTC-ospf-1-area-0.0.0.0] authentication-mode simple
RTC] interface GigabitEthernet0/0
RTC-GigabitEthernet0/0] ospf authentication-mode simple plain 54321
If RTB needs to establish neighbor relationship with RTA and RTC respectively, which of the following configuration needs to be performed on RTB?
A. RTB-ospf-1-area-0.0.0.0] authentication-mode simple RTB] interface GigabitEthernet0/0 RTB-GigabitEthernet0/0] ospf authentication-mode simple plain 12345 RTB] interface GigabitEthernet0/1 RTB-GigabitEthernet0/1 ] ospf authentication-mode simple plain 54321
B. RTB-ospf-1-area-0.0.0.0] authentication-mode simple RTB-ospf-1-area-0.0.0.1] authentication-mode md5 RTB] interface GigabitEthernet0/0 RTB-GigabitEthernet0/0] ospf authentication -mode simple plain 12345 RTB] interface GigabitEthernet0/1 RTB-GigabitEthernet0/1] ospf authentication-mode simple plain 54321
C. RTB-ospf-1-area-0.0.0.0] authentication-mode simple RTB-ospf-1-area-0.0.0.1] authentication-mode simple RTB] interface GigabitEthernet0/0 RTB-GigabitEthernet0/0] ospf authentication -mode simple plain 12345 RTB] interface GigabitEthernet0/1 RTB-GigabitEthernet0/1] ospf authentication-mode simple plain 54321
D. RTB-ospf-1-area-0.0.0.0] authentication-mode simple RTB-ospf-1-area-0.0.0.1] authentication-mode simple RTB] interface GigabitEthernet0/0 RTB-GigabitEthernet0/0] ospf authentication -mode simple plain 12345 RTB] interface GigabitEthernet0/1 RTB-GigabitEthernet0/1] ospf authentication-mode simple plain 12345
正解：C

質問 5：
Running the displaipv6 interface vlan-interface1 verbose command on a router displays the following information:
Vlan-interface1 current state: UP
Line protocol current state:UP
IPv6 is enabled, link-local address is FE80::2010:1
No global unicast address configured
Joined group address(es):
FF02::1:FF10:1
FF02::2
FF02::1
MTU is 1500 btes
ND DAD is enabled, number of DAD attempts: 1
ND reachable time is 30000 milliseconds
ND retransmit interval is 1000 milliseconds
ND advertised reachable time is 0 milliseconds
ND advertised retransmit interval is 0 milliseconds
ND router advertisements are sent ever600 seconds
ND router advertisements live for 1800 seconds
Hosts use stateless autoconfig for addresses
From the above information, it can be known that _______________.
A. The multicast addresses monitored by this interface include FF02::1 , FF02::2 , FF02::1:FF10:1
B. Vlan1 interface is boring and IPv6 protocol status is Up
C. The IPv6 unicast address of the Vlan1 interface is only FE80::2010:1, and the global unicast address is not configured
D. The transmit function of ND RA is not enabled on the Vlan1 interface
正解：A,B,C,D

質問 6：
The PBR configuration on a router is as follows.
policy-based-route pbr_a permit node 10
if-match acl 3000
apploutput-interface serial 2/0
policy-based-route pbr_a dennode 20
if-match acl 3000
Assuming the policy has been successfully applied, how will the data flow configured with Acl3000 on this router be forwarded?
A. Data flow matching Acl 3000 will be forwarded according to policy routing
B. The data flow matching Acl 3000 will be forwarded according to the default route
C. The data flow matching Acl 3000 will be forwarded according to the normal route
D. Data streams matching Acl 3000 will be discarded
正解：A

質問 7：
From RTA to RTD, etc., perform IS-IS networking according to the diagram, and the Stem-IDs of RTA, RTC, and RTD are shown in the diagram.
Then in the following options ______ can be used as the Stem-ID of RTB.
A. 0003.0000.0000
B. 0002.0003.0000
C. 0002.0000.0000
D. 0004.0000.0000
正解：B,C