質問 1：
Select the Exhibit tab.
Your customer has an AFF A300 installed. They ask you to configure the e0a and e0b ports to use the FC protocol.
Referring to the exhibit, which statement is correct in this scenario?
A. These ports are used for the cluster interconnect.
B. These ports are used for the Ethernet uplink into the customer's network.
C. The configuration of these ports can only be done by OnCommand System Manager.
D. Use the ucadmin command to configure these ports as FC ports.
正解：A
質問 2：
Which statement regarding a node-management LIF is true?
A. The LIF can be set up on a dedicated VLAN in the data network.
B. The LIF can be set up on a dedicated VLAN in the cluster network.
C. The LIF must use two switches for redundancy purposes.
D. The LIF can be set only on the built-in node-management port - e0M.
正解：D
質問 3：
A 4-node cluster has connectivity for both block and file access. Nodes 1 and 3 are used for file access, and nodes 2 and 4 are used for block access. During routine maintenance, node 4 is switched off and the LIFs are migrated to other nodes. Upon investigation, you see that the LIFs that serve file traffic have moved to alternative ports. However, LIFs that serve the block have not migrated.
In this scenario, what is happening?
A. The fiber switch is configured incorrectly.
B. The LIFs that serve the block protocol do not failover.
C. The failover group is configured incorrectly.
D. There is a faulty SFP.
正解：A
質問 4：
You are installing a new cluster with a pair of NetApp CN1610 switches.
Which three statements describe how the ports are configured according to NetApp best practices? (Choose three.)
A. All ports have standard frames enabled.
B. All ports have jumbo frames enabled.
C. Ports 1-12 are designated as cluster host ports.
D. Port 13-16 are designated as cluster host ports.
E. Ports 13-16 are designated as Inter-Switch Links (ISLs).
正解：B,C,E
質問 5：
Click the Exhibit button.
You are receiving AutoSupport e-mail from both controllers, but Active IQ is showing updates from only node cl-01-02.
Referring to the exhibit, what is a reason why Active IQ is receiving AutoSupport updates from only node cl-01-02?
A. The service processor is not configured.
B. The cluster management LIF is down.
C. A firewall rule is blocking the AutoSupport.
D. The mail host is blocking the AutoSupport.
正解：D
質問 6：
A customer wants to expand their 10-node AFF A700s SAN cluster on Cisco Nexus 3132Q-V interconnect switches. The customer has six AFF A700s nodes available.
In this scenario, what should you do to expand the cluster?
A. Add two nodes to the existing cluster without exceeding the SAN cluster limit.
B. Add six nodes to the existing cluster.
C. Add an expansion module to each switch and then add the six nodes.
D. Replace the switches with Cisco Nexus 5596T switches and then add the six nodes.
正解：C
質問 7：
Select the Exhibit tab.
You install a new FAS2650 HA with a DS224C disk shelf and ONTAP 9.5 on a customer site.
Referring to the exhibit, which two statements describe what is required to get an HA cabled system? (Choose two.)
A. Insert a cable from right controller port 0a to IOMA port 1, and from port 0b to IOMB port 3.
B. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 4, then cable the out-of-band ACP.
C. Insert a cable from left controller port 0a to IOMB port 1, and from port 0b to IOMA port 3.
D. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 4, then cable the out-of-band ACP.
正解：A,B
質問 8：
You finished an ONTAP 9.5 installation using the information provided by the customer, but the NFS exports and CIFS shares cannot be accessed using the newly created data LIFs.
In this situation, which action should you perform before you leave the customer's site?
A. Advise the customer to solve the issue on their own, this is not part of a basic installation.
B. Review the ONTAP network configuration with the customer and make sure that it is correct.
C. Connect to the customer's switch infrastructure and reset the port configurations.
D. Advise the customer to but Cisco switches because NetApp supports only Cisco switches for CIFS and NFS.
正解：B
質問 9：
According to NetApp best practices, how many NTP servers should you associate with an ONTAP cluster?
A. 4
B. 1
C. 3
D. 2
正解：C
Select the Exhibit tab.
Your customer has an AFF A300 installed. They ask you to configure the e0a and e0b ports to use the FC protocol.
Referring to the exhibit, which statement is correct in this scenario?
A. These ports are used for the cluster interconnect.
B. These ports are used for the Ethernet uplink into the customer's network.
C. The configuration of these ports can only be done by OnCommand System Manager.
D. Use the ucadmin command to configure these ports as FC ports.
正解：A
質問 2：
Which statement regarding a node-management LIF is true?
A. The LIF can be set up on a dedicated VLAN in the data network.
B. The LIF can be set up on a dedicated VLAN in the cluster network.
C. The LIF must use two switches for redundancy purposes.
D. The LIF can be set only on the built-in node-management port - e0M.
正解：D
質問 3：
A 4-node cluster has connectivity for both block and file access. Nodes 1 and 3 are used for file access, and nodes 2 and 4 are used for block access. During routine maintenance, node 4 is switched off and the LIFs are migrated to other nodes. Upon investigation, you see that the LIFs that serve file traffic have moved to alternative ports. However, LIFs that serve the block have not migrated.
In this scenario, what is happening?
A. The fiber switch is configured incorrectly.
B. The LIFs that serve the block protocol do not failover.
C. The failover group is configured incorrectly.
D. There is a faulty SFP.
正解：A
質問 4：
You are installing a new cluster with a pair of NetApp CN1610 switches.
Which three statements describe how the ports are configured according to NetApp best practices? (Choose three.)
A. All ports have standard frames enabled.
B. All ports have jumbo frames enabled.
C. Ports 1-12 are designated as cluster host ports.
D. Port 13-16 are designated as cluster host ports.
E. Ports 13-16 are designated as Inter-Switch Links (ISLs).
正解：B,C,E
質問 5：
Click the Exhibit button.
You are receiving AutoSupport e-mail from both controllers, but Active IQ is showing updates from only node cl-01-02.
Referring to the exhibit, what is a reason why Active IQ is receiving AutoSupport updates from only node cl-01-02?
A. The service processor is not configured.
B. The cluster management LIF is down.
C. A firewall rule is blocking the AutoSupport.
D. The mail host is blocking the AutoSupport.
正解：D
質問 6：
A customer wants to expand their 10-node AFF A700s SAN cluster on Cisco Nexus 3132Q-V interconnect switches. The customer has six AFF A700s nodes available.
In this scenario, what should you do to expand the cluster?
A. Add two nodes to the existing cluster without exceeding the SAN cluster limit.
B. Add six nodes to the existing cluster.
C. Add an expansion module to each switch and then add the six nodes.
D. Replace the switches with Cisco Nexus 5596T switches and then add the six nodes.
正解：C
質問 7：
Select the Exhibit tab.
You install a new FAS2650 HA with a DS224C disk shelf and ONTAP 9.5 on a customer site.
Referring to the exhibit, which two statements describe what is required to get an HA cabled system? (Choose two.)
A. Insert a cable from right controller port 0a to IOMA port 1, and from port 0b to IOMB port 3.
B. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 4, then cable the out-of-band ACP.
C. Insert a cable from left controller port 0a to IOMB port 1, and from port 0b to IOMA port 3.
D. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 4, then cable the out-of-band ACP.
正解：A,B
質問 8：
You finished an ONTAP 9.5 installation using the information provided by the customer, but the NFS exports and CIFS shares cannot be accessed using the newly created data LIFs.
In this situation, which action should you perform before you leave the customer's site?
A. Advise the customer to solve the issue on their own, this is not part of a basic installation.
B. Review the ONTAP network configuration with the customer and make sure that it is correct.
C. Connect to the customer's switch infrastructure and reset the port configurations.
D. Advise the customer to but Cisco switches because NetApp supports only Cisco switches for CIFS and NFS.
正解：B
質問 9：
According to NetApp best practices, how many NTP servers should you associate with an ONTAP cluster?
A. 4
B. 1
C. 3
D. 2
正解：C
0 お客様のコメント