最新なNetwork Appliance NS0-158問題集（83題）、真実試験の問題を全部にカバー！

質問 1：
At which level of granularity would you back up data to tape using the SMTape command?
A. aggregate
B. qtree
C. directory
D. volume
正解：D
解説: (Pass4Test メンバーにのみ表示されます)

質問 2：
Click the exhibit button.

You have a 2-node cluster named cl1 that has separate LIFs on each node for both SAN and NAS traffic.
A storage failover takeover process is initiated as shown in the exhibit.
In this scenario, which two statements about the takeover process are true? (Choose two.)
A. The SAN LIFs on cl1-01 automatically migrate to cl1-02.
B. The NAS LIFs on cl1-01 go offline.
C. The NAS LIFs on cl1-01 automatically migrate to cl1-02.
D. The SAN LIFs on cl1-01 go offline.
正解：C,D
解説: (Pass4Test メンバーにのみ表示されます)

質問 3：
An administrator enabled the iSCSI protocol on an SVM and created a LUN for a Windows
2016 system. After rescan, the LUN is not visible on the host.
Which two steps must the administrator take to solve this problem? (Choose two.)
A. Create an initiator group (igroup), add the iSCSI IQN, and map the igroup to the LUN.
B. Disable the ALUA support from the host for the LUN.
C. Create an initiator group (igroup), add the WWPN of the host initiator, and then map the igroup to the LUN.
D. Configure the iSCSI service on the Windows 2016 system.
正解：A,D
解説: (Pass4Test メンバーにのみ表示されます)

質問 4：
Which type of connectivity is supported when connecting third-party arrays through FlexArray Virtualization for back-end storage to a NetApp cluster?
A. Infiniband
B. SAS
C. FC
D. iSCSI
正解：C
解説: (Pass4Test メンバーにのみ表示されます)

質問 5：
Users report that they are unable to connect to home directories stored on a NetApp cluster. You are using Active Directory-based Kerberos authentication.
Which two actions would correct the problem? (Choose two.)
A. Verify that the CIFS server in running in the SVM.
B. Verify that domain tunneling is configured in ONTAP.
C. Verify that the Network Time Protocol service is in sync.
D. Verify that an Active Directory domain admin account is configured in ONTAP.
正解：A,D
解説: (Pass4Test メンバーにのみ表示されます)

質問 6：
A customer has an aggregate, aggr1_01 with three RAID groups: rg0, rg1, and rg2.
Each RAID group has 15 disks, and the aggregate's maximum RAID group size is set to 18 disks.
The customer adds three additional disks to the aggregate using the following command: storage aggregate add-disks -aggregate aggr1_01 -diskcount 3 How are the RAID groups affected by this command?
A. The three disks are added to RAID group rg0.
B. Each RAID group receives one additional disk.
C. The disks are added to a new RAID group rg3.
D. The three disks are added to RAID group rg2.
正解：D
解説: (Pass4Test メンバーにのみ表示されます)

質問 7：
You have a SnapLock Compliance volume that needs to be replicated to a different cluster at a disaster recovery site.
Which two statements concerning the SnapMirror destination volume are true? (Choose two.)
A. The destination volume type must be SnapLock Enterprise.
B. The destination volume type must be SnapLock Compliance.
C. The destination cluster does not require a SnapLock license.
D. The destination cluster requires a SnapLock license.
正解：B,D
解説: (Pass4Test メンバーにのみ表示されます)

質問 8：
A customer wants to use a UTA2 PCIe card in a new FAS8000 system.
Which three steps must be completed before the customer is able to use the ports for Fc access to an FCP switch? (Choose three.)
A. Verify that the correct SFP+ is installed for FC.
B. Verify that Data ONTAP iSCSI, GIFS, and NFS are licensed on the system.
C. Verify the WWPN of the UTA2 so that these can be used in the igroup to map the LUNs for host access.
D. Use the system hardware unified-connect modify command to change the personality from initiator to target.
E. Verify the card's hardware configuration by running the systemhardware unified-connect show command.
正解：A,D,E