You have recently brought up a QFabric system and now see all of the expected components within the system's inventory. After performing some initial configuration tasks, including the definition of the Node-2:ge-0/0/13 interface, you issue the show interfaces terse command and do not see the defined interface.
What are two reasons for this behavior? (Choose two.)
A. faulty data plane connections between Node-2 and the Interconnect devices
B. unsupported or malfunctioning transceiver
C. malfunctioning fabric control Routing Engines
D. faulty control plane connections between Node-2 and the Director group
正解:A,B
質問 2:
You are configuring a Node group name.
Which statement is correct?
A. DC-CA-ng-1 is a valid name for a new Node group.
B. director-group is a valid name for a new Node group.
C. MyDCNG and mydcng refer to same the components.
D. The maximum length of a Node group name is 8 characters.
正解:A
質問 3:
-- Exhibit -
On node2:
user@node2> show ethernet-switching table
Ethernet-switching tablE. 119 entries, 104 learned
VLAN MAC address Type Age Interfaces vlan200 * Flood - N2:All-members N3:All-members N4:All-members vlan200 00:00:02:00:00:01 Learn 0 N2:ae0.0 vlan200 00:00:02:00:00:02 Learn 0 N2:ae0.0 vlan200 00:00:02:00:00:03 Learn 0 N2:ae0.0 vlan200 00:00:02:00:00:06 Learn 0 N2:ae0.0
On node5:
user@node5> show ethernet-switching table
Ethernet-switching tablE. 119 entries, 104 learned VLAN MAC address Type Age Interfaces vlan200 * Flood - N2:All-members N3:All-members N4:All-members vlan200 00:00:05:00:00:01 Learn 0 N5:ae0.0 vlan200 00:00:05:00:00:02 Learn 0 N5:ae0.0 vlan200 00:00:05:00:00:03 Learn 0 N5:ae0.0 vlan200 00:00:05:00:00:06 Learn 0 N5:ae0.0
user@node5>show route forwarding-table family ethernet-switching vlan vlan200---qfabric Routing tablE. default.ethernet-switching Destination Type RtRef Next hop Type Index NhRef Netif 7, * user 0 comp 1676 2 7, * intf 0 rslv 1650 1 7, 00:00:02:00:00:01 user 0 comp 1673 51
7, 00:00:02:00:00:02 user 0 comp 1673 51 7, 00:00:02:00:00:03 user 0 comp 1673 51 7, 00:00:02:00:00:05 user 0 comp 1673 51 7, 00:00:02:00:00:06 user 0 comp 1673 51
user@qfabric>show route fabric table default.bridge.0 bridge-route-mac-address
00:00:02:00:00:01
default.bridge.0: 110 destinations, 165 routes (110 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both -- Exhibit -
Click the Exhibit button.
Referring to the exhibit, Host A on Node device node2 and Host B on Node device node5 are on the same VLAN but Host A cannot ping Host B.
Host A's MAC address is 00:00:02:00:00:01.
Host B's MAC address is 00:00:05:00:00:01.
What is causing this problem?
A. The MAC address of Host A is not learned in node2.
B. Host B is not connected to Node device node5.
C. The MAC address of Host B is not learned in node5.
D. The MAC address of Host A is not in the RPDf table of Node device node5.
正解:D
質問 4:
Which routing table is used to exchange Layer 3 routes between components in a QFabric system?
A. default.inet.0
B. inet.0
C. bgp.vpn-inet.0
D. bgp.inet.0
正解:A
質問 5:
Which Routing Engine (RE) in a QFabric system acts as a BGP route reflector for internal reachability?
A. the fabric control RE
B. the fabric manager RE
C. the network Node group RE
D. the server Node group RE
正解:A
質問 6:
You are determining the DC power requirements for a QFX3000-M QFabric system.
Which two devices support DC power? (Choose two.)
A. a QFX3500 Node device
B. a QFX3800-I Interconnect device
C. a QFX3600-I Interconnect device
D. a QFX3100 Director device
正解:A,C
浅见** -
試験を受ける前に、この問題集で勉強しました。JN0-370本番の試験でも同じ問題がいくつか出題されました。