最新なIBM C4040-121問題集（102題）、真実試験の問題を全部にカバー！

質問 1：
An administrator is planning to upgrade their VIO Server (VIOS) 1.5 partition to the latest level using DVD media. The VIOS partition is HMC managed and contained in the CEO.
What does the administrator require to perform the upgrade?
A. The Migration DVD, Update DVD and latest Fixes on media utilizing the CEO media tray
B. The Installation DVD, Update DVD and latest Fixes on media utilizing the CEO media tray
C. The Installation DVD, Update DVD and latest Fixes on media utilizing the HMO media tray
D. The Migration DVD, Update DVD and latest Fixes on media utilizing the HMO media tray
正解：A

質問 2：
A system needs maintenance that requires the entire system to be brought down. The system is running multiple IBM i partitions, all being hosted by and all resources owned by VIO Server (VIOS).
After performing the maintenance, VIOS is brought back up and IBM i partitions are reactivated. Two partitions have SPO codes indicating they cannot find disk drives.
What is the most likely cause?
A. The partitions have multiple profiles, and a profile with an incorrectTagged I/O Load Source was used.
B. vSCSI controllers were added to the client partition using DLPAR, but never permanently added to the profile.
C. VIOServer has not completed the boot process.
D. There is an incompatibilitywith server firmware and VIOS code.
正解：B

質問 3：
A POWER7 system has two IBM i client partitions utilizing dual VIO Server (VIOS) partitions for all disk & LAN resources. In order to provide uninterrupted operations when either of the VIOS partitions is shut down, what is the minimum number of virtual adapters that must be created in each VIOS partition?
A. 1
B. 3
C. 6
D. 2
正解：B

質問 4：
The DSPFMWSTS on an IBM i 7.1 partition appears as shown:

As part of troubleshooting, IBM support asks that level AL730_087 be deactivated.
How is that accomplished?
A. Stop all partitions Change the managed system to start in "P" mode Restart the managed system From the HMC, select Updates
B. Run command RMVPTF LICPGM(5770SS1) SELECT(MH01310) DELAYED(*YES), then restart the partition
C. Run command DLTPTF PTF(MH01310) RMV(*TEMP)
D. On the resulting screen, select the managed system Under Tasks select Change Licensed Internal Code for Current Release In the wizard select Deactivate Temporary Level
正解：A

質問 5：
On an HMC under Systems Management and Servers there are three servers listed. One of them shows "no connection." The HMC can ping the configured ESP address. The server has power and the front panel displays HMC=0 in the lower left.
Which action is valid for this connection?
A. Operations-> Launch ASM
B. Properties
C. Operations-> Power On
D. Operations-> Change Password
正解：A

質問 6：
A processor upgrade to a new 4-core Power 720 is planned, with processors capped and shared processor pools enabled, using the following configuration:
IBM i: Minimum - 1 .0; Desired - 2.5; Maximum - 2.5
Linux: Minimum - 0.5; Desired - 1.0; Maximum - 1.0
AIX: Minimum - 0.5; Desired - 0.5; Maximum - 1 .0
How many processor entitlements for IBM i are required on the new system?
A. 4
B. 1
C. 3
D. 2
正解：C

質問 7：
A customer has purchased a new BladeCenter H (BCH) and POWER blade to run IBM i. The POWER blade is configured with two Fibre Channel interlaces for attaching SAN and tape.
They have an IBM TS3500 tape library with a fibre channel connection, and current firmware is running through a fibre switch to another IBM i system. One port on the existing switch and one port in the BCH fibre switch has been zoned to provide a connection from the tape library to the BCH.
After IBM i 7.1 SLIC and base OS are installed on the blade from IBM distribution media, the tape library does not appear in the device configuration.
What is the most likely cause of the problem?
A. NPIV enablement was omitted when configuring the BCH switch.
B. The existing switch does not support NPIV.
C. The BCH switch configuration must match the link speed of the TS3500.
D. A switch-to-switch cable is required. A switch to device cable was shipped with the BCH by default.
正解：B

質問 8：
A POWER7 system has 6 IBM i partitions sharing a single shared processor pool. The system has 3 IBM i operating system licenses. Without exceeding the licenses available, what is the largest allowable value for the "Maximum processing units" setting in the shared processor pool?
A. 1
B. 3
C. 6
D. 2
正解：B

質問 9：
Auditors have reviewed access to the HMC and determined that many users have too much authority on the HMC. What is the correct method to restrict users to only a specific set of resources?
A. Create and assign a new task role that allows only the required set of tasks.
B. Change the users' task role to hmcoperator.
C. Create and assign a new resource role that allows access to only the required resources.
D. In Manage Users and Tasks, select each resource that is required for this user.
正解：C