-- Exhibit -

-- Exhibit --
Refer to the exhibit. When USER1 tried to map shares to Server 1 and Server 2, he got the results shown.
What does the report represent? (Select 2)
A. The connection to Server 1 is optimized, with errors, the performance should be poor.
B. The connection to Server 1 is optimized. The performance should be good.
C. The connection to Server 2 is optimized, with errors, the performance should be poor.
D. The connection to Server 2 is optimized. The performance should be good.
E. The connection to Server 1 is not being optimized.
正解:A,D
質問 2:
In order to reset the admin password that has been lost, the procedure can be done via what type of connection to a Steelhead appliance?
A. Serial cable connection
B. SSH over AUX interface IP
C. SSH over Primary interface IP
D. Password recovery can not be done on a Steelhead appliance
E. SSH over in-path interface IP
正解:A
質問 3:
RiOS v7.0 and later, the packet-mode-optimization feature can: (Select 2)
A. optimize UDP IPv6
B. optimize TCP IPv4
C. optimize UDP IPv4
D. optimize TCP IPv6
正解:C,D
質問 4:
What configuration policies can be used on the SteelCentral Controller for SteelHead (SCC) for Interceptor deployments?
A. The SCC can be used to create cluster policies, for the Interceptor to SteelHead connections only and not in-path or load balancing rules.
B. The SCC can be used to configure the cluster of registered Interceptors and SteelHeads. Then, in-path rules and load balancing rules can be pushed to the interceptors.
C. The SCC can be used to create all configuration for the Interceptors and its associated SteelHeads, as long as all the devices are in the same SCC group.
D. The SCC can create in-path rules policies the same as a SteelHead, as long as that is the only page enabled for the Interceptor.
E. The SCC can only monitor the health, backup the configuration and upgrade Interceptors. Policies are only for SteelHeads. Interceptors and SteelHead Mobile are not supported.
正解:B
質問 5:
What is required for the Embedded Cascade Shark function to work? (Select 3)
A. You must give the username Shark a password.
B. The optimization service needs to be restarted.
C. You must enable Cascade Shark on the Management Console TCP Dumps menu.
D. TCP port 61898 should be open between the Steelhead and the remote Cascade Pilot.
正解:A,C,D
質問 6:
Where are SDR references maintained on a Steelhead appliance?
A. Persistent storage
B. USB keys
C. Configuration file
D. Flash storage
E. RSP partition
正解:A
質問 7:
The default setting for "allow failure" in the Interceptor appliance version 2.0 is: (Select 2)
A. Is configurable
B. Disabled by default
C. Enabled by default
D. Is not configurable
正解:A,B
質問 8:
SH10 and SH11 are connection forwarding neighbors. After a configuration change on SH11, SH10 is in
"degraded" status. What is the possible cause? (Select 2)
A. The connection forwarding keepalive cable was disconnected.
B. The optimization services on SH10 are not running.
C. Connection forwarding is disabled on SH11.
D. The optimization services on SH11 are not running.
正解:C,D
質問 9:
You have an in-house HTTP application running on port 8443 but you are not seeing HTTP optimization. You checked and made sure that the HTTP blade is enabled. What is the likely problem?
A. There is a separate license key for the HTTP blade
B. Primary port needs to be on the LAN side of the Steelhead
C. The HTTP blade only supports HTTP 1.1 and the application is using HTTP 1.0
D. The HTTP blade will only work on port 80 and 8080 and can not be changed
E. HTTP blade is enabled by default on port 80 and 8080. An in-path rule is necessary for all other ports.
正解:E
大原** -
この830-01テキストもやる気がわいてくるような気がします。きっちりとまとまっていてわかりやすかったです。