最新なFortinet NSE7_EFW-6.2問題集（105題）、真実試験の問題を全部にカバー！

質問 1：
Refer to exhibit, which contains the output of a BGP debug command.

Which statement explains why the state of the 10.200.3.1 peer is Connect?
A. The TCP session to 10.200.3.1 has not completed the 3-way handshake.
B. The local router is receiving the BGP keepalives from the peer, but it has not received a BGP prefix yet.
C. The local router has received the BGP prefixes from the remote peer.
BGP neighbor states and how they change: * Idle: Initial state * Connect: Waiting for a successful three-way TCP connection * Active: Unable to establish the TCP session * OpenSent: Waiting for an OPEN message from the peer * OpenConfirm: Waiting for the keepalive message from the peer * Established: Peers have successfully exchanged OPEN and keepalive messages
D. The local router is receiving BGP keepalives from the remote peer, but the local peer has not received the OpenConfirm yet.
正解：A

質問 2：
View the exhibit, which contains the output of a debug command, and then answer the question below.

Which one of the following statements about this FortiGate is correct?
A. It is currently in extreme conserve mode because of high memory usage.
B. It is currently in proxy conserve mode because of high memory usage.
C. It is currently in memory conserve mode because of high memory usage.
D. It is currently in system conserve mode because of high CPU usage.
正解：C

質問 3：
View the central management configuration shown in the exhibit, and then answer the question below.

Which server will FortiGate choose for antivirus and IPS updates if 10.0.1.243 is experiencing an outage?
A. 10.0.1.244
B. 10.0.1.242
C. One of the public FortiGuard distribution servers
D. 10.0.1.240
正解：C

質問 4：
View the exhibit, which contains the output of a BGP debug command, and then answer the question below.

Which of the following statements about the exhibit are true? (Choose two.)
A. The local BGP peer has received a total of three BGP prefixes.
B. Since the BGP counters were last reset, the BGP peer 10.200.3.1 has never been down.
C. The local BGP peer has not established a TCP session to the BGP peer 10.200.3.1.
D. For the peer 10.125.0.60, the BGP state of is Established.
正解：C,D

質問 5：
View the exhibit, which contains the output of a diagnose command, and the answer the question below.

Which statements are true regarding the Weight value?
A. Its initial value is statically set to 10.
B. It determines which FortiGuard server is used for license validation.
C. Its initial value is calculated based on the round trip delay (RTT).
D. Its value is incremented with each packet lost.
正解：D

質問 6：
Examine the following partial outputs from two routing debug commands; then answer the question below:

Why the default route using port2 is not displayed in the output of the second command?
A. It has a higher distance than the default route using port1.
B. It has a higher priority than the default route using port1.
C. It has a lower priority than the default route using port1.
D. It is disabled in the FortiGate configuration.
正解：A
解説: (Pass4Test メンバーにのみ表示されます)

質問 7：
View the exhibit, which contains the output of a debug command, and then answer the question below.

What statement is correct about this FortiGate?
A. It is currently in system conserve mode because of high memory usage.
B. It is currently in FD conserve mode.
C. It is currently in system conserve mode because of high CPU usage.
D. It is currently in kernel conserve mode because of high memory usage.
正解：A