716 お客様のコメント
クリック」
質問 1：
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
A. Require the Applicator to remove the coating
B. Ignore the situation
C. Stop the job
D. Advise the Owner and write a Non-Conformance report
正解：A
質問 2：
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
A. Sacking
B. Acid etching
C. Stoning
D. High-pressure water washing
正解：A
質問 3：
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
A. Advise the other inspector he is using an incorrect method
B. Review the specification with the other inspector to see what method was specified
C. Advise your QC Manager to change the ITP to the use of the salt smart meter
D. Redo the pre-cleaning based on the other inspectors results
正解：B
質問 4：
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:
A. Correct the errors yourself and submit the reports without any further action
B. Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent
C. Correct the errors yourself and suggest the Level 1 inspector be replaced
D. Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation
正解：D
質問 5：
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
A. A very high reading
B. A very low reading
C. No difference from any other coating
D. Cold flow or creep
正解：D
質問 6：
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
A. Fusion Bonded Epoxy
B. 2-Layer Polyethylene (PE)
C. 3-Layer Polyethylene (PE)
D. Coal Tar Enamel
正解：C
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
A. Require the Applicator to remove the coating
B. Ignore the situation
C. Stop the job
D. Advise the Owner and write a Non-Conformance report
正解：A
質問 2：
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
A. Sacking
B. Acid etching
C. Stoning
D. High-pressure water washing
正解：A
質問 3：
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
A. Advise the other inspector he is using an incorrect method
B. Review the specification with the other inspector to see what method was specified
C. Advise your QC Manager to change the ITP to the use of the salt smart meter
D. Redo the pre-cleaning based on the other inspectors results
正解：B
質問 4：
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:
A. Correct the errors yourself and submit the reports without any further action
B. Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent
C. Correct the errors yourself and suggest the Level 1 inspector be replaced
D. Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation
正解：D
質問 5：
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
A. A very high reading
B. A very low reading
C. No difference from any other coating
D. Cold flow or creep
正解：D
質問 6：
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
A. Fusion Bonded Epoxy
B. 2-Layer Polyethylene (PE)
C. 3-Layer Polyethylene (PE)
D. Coal Tar Enamel
正解：C
铃木** -
NACE新の試験問題に徹底対応した、NACE-CIP2-001受験生必携の問題集です。Pass4Testの問題集を買うのが二回目になります。