821 お客様のコメント
質問 1：
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?
A. SP 1 followed by SP 3
B. SP 1 followed by SP 2
C. SP 1 followed by acid etching
D. SP 1 followed by caustic etching
正解：B
質問 2：
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
A. The floating structure is stationary
B. It contains biocide
C. It doesn't contain biocide
D. It will result in a very slippery surface
正解：B
質問 3：
In the event of a conflict between the Product Data Sheet and the Specification:
A. The Specification prevails
B. It is up to the Inspector to decide which one to follow
C. The Product Data Sheet prevails
D. It is up to the Applicator to decide which one to follow
正解：A
質問 4：
Dehumidification is defined as the removal of moisture vapor from the air to
A. lower its temperature
B. provide worker comfort.
C. raise its relative humidity.
D. lower its dew point,
正解：D
質問 5：
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
A. Fusion Bonded Epoxy
B. 2-Layer Polyethylene (PE)
C. 3-Layer Polyethylene (PE)
D. Coal Tar Enamel
正解：C
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?
A. SP 1 followed by SP 3
B. SP 1 followed by SP 2
C. SP 1 followed by acid etching
D. SP 1 followed by caustic etching
正解：B
質問 2：
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
A. The floating structure is stationary
B. It contains biocide
C. It doesn't contain biocide
D. It will result in a very slippery surface
正解：B
質問 3：
In the event of a conflict between the Product Data Sheet and the Specification:
A. The Specification prevails
B. It is up to the Inspector to decide which one to follow
C. The Product Data Sheet prevails
D. It is up to the Applicator to decide which one to follow
正解：A
質問 4：
Dehumidification is defined as the removal of moisture vapor from the air to
A. lower its temperature
B. provide worker comfort.
C. raise its relative humidity.
D. lower its dew point,
正解：D
質問 5：
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
A. Fusion Bonded Epoxy
B. 2-Layer Polyethylene (PE)
C. 3-Layer Polyethylene (PE)
D. Coal Tar Enamel
正解：C
Yamanaka -
Pass4Testに書いた文字通り『出るとこだけ』ですね。NACE-CIP2-001本番試験の7割強を得点できました。