988 お客様のコメント
質問 1：
Three IS-IS routers on a broadcast segment have different priority values configured.
Which router is elected the DIS on that broadcast segment?
A. the router with the highest IP address
B. the router with the lowest priority
C. the router with the highest System ID
D. the router with the highest priority
正解：D
質問 2：
Two Level 2 routers are exchanging Hello packets with different Area IDs. What occurs between these routers?
A. No IS-IS PDUs are sent.
B. An Adjacency forms but traffic is not forwarded.
C. An Adjacency does not form.
D. An Adjacency forms.
正解：D
質問 3：
If all OSPF routers on a broadcast network have the same OSPF priority, what parameter is used to determine the new BDR at the time of a DR failure?
A. area ID
B. router ID
C. IP address of interface on broadcast network
D. loopback address
正解：B
質問 4：
What command would you use to view an IS-IS adjacency?
A. show iso adjacency
B. show isis adjacency
C. show isis neighbor
D. show iso neighbor
正解：B
質問 5：
A network administrator would like to verify the active alarms on interface so-0/0/0.0. Which command displays this information?
A. show interfaces extensive
B. show interfaces terse
C. show alarms extensive
D. show alarms
正解：A
質問 6：
Which CLI command shows the BGP options that have been negotiated between peers?
A. show bgp route
B. show bgp options
C. show bgp summary
D. show bgp neighbor
正解：D
質問 7：
Route preference is used to differentiate between _____.
A. two routes received from the same AS
B. two routes received from different routing protocols
C. two routes received from the same routing protocol
D. internal and external BGP routes
正解：B
質問 8：
From the [edit] level of the configuration hierarchy, which command assigns a router its autonomous system number?
A. set routing-options autonomous-system
B. set protocols bgp autonomous-system
C. set routing-options bgp autonomous-system
D. set protocols bgp group ibgp autonomous-system
正解：A
Three IS-IS routers on a broadcast segment have different priority values configured.
Which router is elected the DIS on that broadcast segment?
A. the router with the highest IP address
B. the router with the lowest priority
C. the router with the highest System ID
D. the router with the highest priority
正解：D
質問 2：
Two Level 2 routers are exchanging Hello packets with different Area IDs. What occurs between these routers?
A. No IS-IS PDUs are sent.
B. An Adjacency forms but traffic is not forwarded.
C. An Adjacency does not form.
D. An Adjacency forms.
正解：D
質問 3：
If all OSPF routers on a broadcast network have the same OSPF priority, what parameter is used to determine the new BDR at the time of a DR failure?
A. area ID
B. router ID
C. IP address of interface on broadcast network
D. loopback address
正解：B
質問 4：
What command would you use to view an IS-IS adjacency?
A. show iso adjacency
B. show isis adjacency
C. show isis neighbor
D. show iso neighbor
正解：B
質問 5：
A network administrator would like to verify the active alarms on interface so-0/0/0.0. Which command displays this information?
A. show interfaces extensive
B. show interfaces terse
C. show alarms extensive
D. show alarms
正解：A
質問 6：
Which CLI command shows the BGP options that have been negotiated between peers?
A. show bgp route
B. show bgp options
C. show bgp summary
D. show bgp neighbor
正解：D
質問 7：
Route preference is used to differentiate between _____.
A. two routes received from the same AS
B. two routes received from different routing protocols
C. two routes received from the same routing protocol
D. internal and external BGP routes
正解：B
質問 8：
From the [edit] level of the configuration hierarchy, which command assigns a router its autonomous system number?
A. set routing-options autonomous-system
B. set protocols bgp autonomous-system
C. set routing-options bgp autonomous-system
D. set protocols bgp group ibgp autonomous-system
正解：A
Mizusawa -
JN0-201のこういう問題集はあると非常に重宝します。加点ポイント高いです。Pass4Testさんのお陰でいい内容に出会いました。幸せです。