818 お客様のコメント
質問 1：
After consulting with the network team, it is decided that Transport Zones will be configured with Unicast Replication Mode for a new NSX for vSphere deployment.
Which statement is true regarding the function of the VXLAN Tunnel End Points (VTEPs)?
A. The VTEPs will send multicast frames to all other VTEPs in the Transport Zone when the VTEPs do not have a MAC address in the MAC table.
B. The VTEPs will send unicast frames to all local VTEPs and remote proxies in the Transport Zone when the VTEPs do not have a MAC address in the MAC table.
C. The VTEPs will switch to Multicast Replication Mode for those VTEPs to which multicast path discovery is successful.
D. The VTEPs will send unicast frames to the NSX Controllers when the VTEPs do not have a MAC address in the MAC table.
正解：B
質問 2：
An administrator has received reports of intermittent connectivity between virtual machines on an NSX network. The network team has verified that all physical network devices have been set to 1600 MTU.
What other configuration could cause this issue?
A. An MTU value of 1500 on the distributed firewall
B. An MTU value of 1500 on the logical load balancer
C. An MTU value of 1500 on the vDS Switch
D. An MTU value of 1500 on the logical router
正解：C
質問 3：
How is the Bridge Instance chosen?
A. It is manually assigned by the vSphere administrator when the distributed portgroup is configured.
B. It is chosen based on the ESXi host where the Logical Router Control VM is running.
C. The VTEP configured with the highest VXLAN Network Identifier (VNI) is selected.
D. During an election process among all ESXi hosts. The host with the highest MAC address is selected.
正解：B
質問 4：
Which two statements are true regarding Layer 2 VPNs? (Choose two.)
A. The Distributed Router can form a Layer 2 VPN to another Distributed Router or NSX Edge Service Gateway.
B. Layer 2 VPNs are used to securely extend Ethernet segments over an untrusted medium.
C. The NSX Edge Service Gateway can form a Layer 2 VPN with a standards-compliant physical appliance.
D. Layer 2 VPNs require the two VPN endpoints be in the same Layer 2 segment.
正解：B,C
質問 5：
Which Layer 2 bridge is supported by the Distributed Router?
A. VXLAN to PVLAN bridge
B. VCD-NI to PVLAN bridge
C. VCD-NI to VLAN bridge
D. VXLAN to VLAN bridge
正解：D
質問 6：
You want to use an existing NSX Manager to extend logical networks to the ESXi hosts of a new cluster.
What should you do?
A. On the Installation > Management page of the Networking & Security section of the vSphere Web Client, click the green plus sign to deploy a new NSX controller node to the new cluster.
B. On the Installation > Host Preparation page of the Networking & Security section of the vSphere Web Client, click the Install link for the new cluster.
C. On the Installation > Host Preparation page of the Networking & Security section of the vSphere Web Client, click the Install link for each of the new hosts.
D. On the Installation > Logical Network Preparation page of the Networking & Security section of the vSphere Web Client, create a new Transport Zone for the new cluster.
正解：B
質問 7：
What is the default delay when the active NSX Edge instance fails before the standby instance takes the active role?
A. 6 seconds.
B. 15 seconds.
C. 45 seconds.
D. 3 seconds.
正解：B
After consulting with the network team, it is decided that Transport Zones will be configured with Unicast Replication Mode for a new NSX for vSphere deployment.
Which statement is true regarding the function of the VXLAN Tunnel End Points (VTEPs)?
A. The VTEPs will send multicast frames to all other VTEPs in the Transport Zone when the VTEPs do not have a MAC address in the MAC table.
B. The VTEPs will send unicast frames to all local VTEPs and remote proxies in the Transport Zone when the VTEPs do not have a MAC address in the MAC table.
C. The VTEPs will switch to Multicast Replication Mode for those VTEPs to which multicast path discovery is successful.
D. The VTEPs will send unicast frames to the NSX Controllers when the VTEPs do not have a MAC address in the MAC table.
正解：B
質問 2：
An administrator has received reports of intermittent connectivity between virtual machines on an NSX network. The network team has verified that all physical network devices have been set to 1600 MTU.
What other configuration could cause this issue?
A. An MTU value of 1500 on the distributed firewall
B. An MTU value of 1500 on the logical load balancer
C. An MTU value of 1500 on the vDS Switch
D. An MTU value of 1500 on the logical router
正解：C
質問 3：
How is the Bridge Instance chosen?
A. It is manually assigned by the vSphere administrator when the distributed portgroup is configured.
B. It is chosen based on the ESXi host where the Logical Router Control VM is running.
C. The VTEP configured with the highest VXLAN Network Identifier (VNI) is selected.
D. During an election process among all ESXi hosts. The host with the highest MAC address is selected.
正解：B
質問 4：
Which two statements are true regarding Layer 2 VPNs? (Choose two.)
A. The Distributed Router can form a Layer 2 VPN to another Distributed Router or NSX Edge Service Gateway.
B. Layer 2 VPNs are used to securely extend Ethernet segments over an untrusted medium.
C. The NSX Edge Service Gateway can form a Layer 2 VPN with a standards-compliant physical appliance.
D. Layer 2 VPNs require the two VPN endpoints be in the same Layer 2 segment.
正解：B,C
質問 5：
Which Layer 2 bridge is supported by the Distributed Router?
A. VXLAN to PVLAN bridge
B. VCD-NI to PVLAN bridge
C. VCD-NI to VLAN bridge
D. VXLAN to VLAN bridge
正解：D
質問 6：
You want to use an existing NSX Manager to extend logical networks to the ESXi hosts of a new cluster.
What should you do?
A. On the Installation > Management page of the Networking & Security section of the vSphere Web Client, click the green plus sign to deploy a new NSX controller node to the new cluster.
B. On the Installation > Host Preparation page of the Networking & Security section of the vSphere Web Client, click the Install link for the new cluster.
C. On the Installation > Host Preparation page of the Networking & Security section of the vSphere Web Client, click the Install link for each of the new hosts.
D. On the Installation > Logical Network Preparation page of the Networking & Security section of the vSphere Web Client, create a new Transport Zone for the new cluster.
正解：B
質問 7：
What is the default delay when the active NSX Edge instance fails before the standby instance takes the active role?
A. 6 seconds.
B. 15 seconds.
C. 45 seconds.
D. 3 seconds.
正解：B
仓*翠 -
このVCAN610は初心者にとってはわかりやすい素晴らしい問題集になっております。試験に受かりましたよ。