1133 お客様のコメント
質問 1：
Refer to the exhibit.
A FortiAnalyzer report is shown.
You must extract relevant information provided by the report regarding your OT network.
Which two statements are correct? (Choose two.)
A. The targeted IP address of the attacks is 10.1.5.1.
B. The report covers the last day.
C. The attacks are blocked.
D. Modbus traffic is reported.
正解：C,D
解説: (Pass4Test メンバーにのみ表示されます)
質問 2：
During layer 2 polling , which two pieces of information are gathered by FortiNAC to identify a device?
(Choose two answers)
A. Where it was learned
B. The system name learned
C. The MAC-to-IP correlation learned
D. The time it was learned
正解：A,D
質問 3：
Refer to the exhibit.
A Logical Topology page of a FortiGate device is shown. Your OT company wants to gain visibility into the network. You decide to implement device detection with the Security Fabric. Based on the exhibit, which statement is correct? (Choose one answer)
A. Device Detection is enabled on port3.
B. Device Detection is enabled on the other identified device.
C. The other identified device must be authorized on the root FortiGate.
D. The other identified device must be authorized on FortiAnalyzer.
正解：B
解説: (Pass4Test メンバーにのみ表示されます)
質問 4：
You want FortiAnalyzer to trigger an automation stitch on a FortiGate device automatically. What must you configure on FortiAnalyzer to enable direct communication with FortiGate? (Choose one answer)
A. An event handler
B. The Fabric settings
C. A Fabric connector
D. A playbook task
正解：B
解説: (Pass4Test メンバーにのみ表示されます)
質問 5：
Refer to the exhibit.
The configuration of firewall policies is shown.
To improve the security of your OT network, you have configured authentication in the firewall policies as shown in the exhibit, with CLI parameters set to their default settings. However, when you test HTTPS access from the LAN subnet to PLC-1, it is successful without any authentication prompt.
What is the reason?
A. You are passively authenticated.
B. You are authenticated with the default implicit firewall policy.
C. You did not configure authentication in firewall policy ID 9.
D. You must first authenticate using a protocol such as HTTP or Telnet.
正解：C
解説: (Pass4Test メンバーにのみ表示されます)
Refer to the exhibit.
A FortiAnalyzer report is shown.
You must extract relevant information provided by the report regarding your OT network.
Which two statements are correct? (Choose two.)
A. The targeted IP address of the attacks is 10.1.5.1.
B. The report covers the last day.
C. The attacks are blocked.
D. Modbus traffic is reported.
正解：C,D
解説: (Pass4Test メンバーにのみ表示されます)
質問 2：
During layer 2 polling , which two pieces of information are gathered by FortiNAC to identify a device?
(Choose two answers)
A. Where it was learned
B. The system name learned
C. The MAC-to-IP correlation learned
D. The time it was learned
正解：A,D
質問 3：
Refer to the exhibit.
A Logical Topology page of a FortiGate device is shown. Your OT company wants to gain visibility into the network. You decide to implement device detection with the Security Fabric. Based on the exhibit, which statement is correct? (Choose one answer)
A. Device Detection is enabled on port3.
B. Device Detection is enabled on the other identified device.
C. The other identified device must be authorized on the root FortiGate.
D. The other identified device must be authorized on FortiAnalyzer.
正解：B
解説: (Pass4Test メンバーにのみ表示されます)
質問 4：
You want FortiAnalyzer to trigger an automation stitch on a FortiGate device automatically. What must you configure on FortiAnalyzer to enable direct communication with FortiGate? (Choose one answer)
A. An event handler
B. The Fabric settings
C. A Fabric connector
D. A playbook task
正解：B
解説: (Pass4Test メンバーにのみ表示されます)
質問 5：
Refer to the exhibit.
The configuration of firewall policies is shown.
To improve the security of your OT network, you have configured authentication in the firewall policies as shown in the exhibit, with CLI parameters set to their default settings. However, when you test HTTPS access from the LAN subnet to PLC-1, it is successful without any authentication prompt.
What is the reason?
A. You are passively authenticated.
B. You are authenticated with the default implicit firewall policy.
C. You did not configure authentication in firewall policy ID 9.
D. You must first authenticate using a protocol such as HTTP or Telnet.
正解：C
解説: (Pass4Test メンバーにのみ表示されます)
Kitahara -
持ち歩きは面倒というのであれば、全ページが電子化されているので、PDFファイルでダウンロードすることもできるところが大好きです。解釈でわかりやく内容を明示。つまづきやすいポイントをフォローしてくれてる。Pass4Testさんの押さえるべきポイントを確実に覚えればなかなかNSEI_OTS_AR-7.6試験でいい点は取れると思う。