質問 1：
The root aggregate on your single-node ONTAP cluster failed. You have the configuration backups saved on your FTP server?
In this scenario, which two steps are part of the recovery procedure? (Choose two.)
A. Boot into maintenance mode.
B. Create a new root aggregate and set its ha_policy option to cfo.
C. Perform a Netboot using the configuration backup.
D. Create a new aggregate and set its ha_policy option to sfo.
正解：A,B
質問 2：
Click the exhibit button.
You are investigating an AutoSupport Disk Redundancy Failed alert. Cluster A lost connectivity to storage bridge BrB1, while cluster B lost connectivity to storage bridge BrA1.
Referring to the exhibit, which three components need investigation? (Choose three.)
A. FC switch SwA1
B. FC switch SwA2
C. ISL cables
D. storage bridges BrB1
E. FC switch SwB1
正解：A,C,E
質問 3：
A customer has a 2-node MetroCluster. They experienced a complete power loss at site B.
The customer has
lost connectivity to site B and now realizes that the DR partner at site A has not taken over the DR partner at site B.
Which two actions must be performed in this scenario? (Choose two.)
A. On the DR partner at site A, perform the process to heal the data aggregates.
B. Ensure that site B is prevented from serving data or simply powered off (nodes and disk shelves).
C. On the DR partner at site B, perform the process to heal the root aggregate.
D. On the DR partner at site A, perform the process to switchover.
正解：C,D
質問 4：
Click the exhibit button.
A customer has an FC SAN with brocade switches. Each server attached to the SAN gas four FC ports. The customer describes that one of their servers has only four paths to the LUNs configured on the cluster. There should be eight paths on all the other servers. The switch administrator has verified the zone configuration.
Referring to the exhibit, which two actions would you perform to troubleshoot the problem? (Choose two.)
A. Review the igroup configuration on the cluster.
B. Review the LIF configuration on the cluster.
C. Review that the host side FC link ports are enabled.
D. Review the driver version on the server.
正解：B,D
質問 5：
Click the exhibit button.
A customer reports that their system recently began logging an error.
Referring to the exhibit, which two statements are correct? (Choose two.)
A. A user is attempting to restart the ntpd daemon.
B. The ntpd daemon is responsible for time services.
C. The spmd application failed to restart the ntpd daemon.
D. The bcomd application is responsible for monitoring the observed behavior.
正解：A,B
質問 6：
A customer has created an interface group (igroup) named a0a, a VLAN named a0a-2500, and a data LIF associated with the VLAN interface that has been assigned an IP of 10.254.10.100. The customer is able to ping 10.254.10.100 from a Windows client without any issues, but data traffic is not working.
In this scenario, what is the solution to the problem?
A. Correct the MTU mismatch between the broadcast domain configuration and the upstream network switches.
B. Disable flow control on the a0a interface.
C. Allow data traffic by using LIF firewall policies.
D. Configure an appropriate service policy for the data LIF.
正解：C
The root aggregate on your single-node ONTAP cluster failed. You have the configuration backups saved on your FTP server?
In this scenario, which two steps are part of the recovery procedure? (Choose two.)
A. Boot into maintenance mode.
B. Create a new root aggregate and set its ha_policy option to cfo.
C. Perform a Netboot using the configuration backup.
D. Create a new aggregate and set its ha_policy option to sfo.
正解：A,B
質問 2：
Click the exhibit button.
You are investigating an AutoSupport Disk Redundancy Failed alert. Cluster A lost connectivity to storage bridge BrB1, while cluster B lost connectivity to storage bridge BrA1.
Referring to the exhibit, which three components need investigation? (Choose three.)
A. FC switch SwA1
B. FC switch SwA2
C. ISL cables
D. storage bridges BrB1
E. FC switch SwB1
正解：A,C,E
質問 3：
A customer has a 2-node MetroCluster. They experienced a complete power loss at site B.
The customer has
lost connectivity to site B and now realizes that the DR partner at site A has not taken over the DR partner at site B.
Which two actions must be performed in this scenario? (Choose two.)
A. On the DR partner at site A, perform the process to heal the data aggregates.
B. Ensure that site B is prevented from serving data or simply powered off (nodes and disk shelves).
C. On the DR partner at site B, perform the process to heal the root aggregate.
D. On the DR partner at site A, perform the process to switchover.
正解：C,D
質問 4：
Click the exhibit button.
A customer has an FC SAN with brocade switches. Each server attached to the SAN gas four FC ports. The customer describes that one of their servers has only four paths to the LUNs configured on the cluster. There should be eight paths on all the other servers. The switch administrator has verified the zone configuration.
Referring to the exhibit, which two actions would you perform to troubleshoot the problem? (Choose two.)
A. Review the igroup configuration on the cluster.
B. Review the LIF configuration on the cluster.
C. Review that the host side FC link ports are enabled.
D. Review the driver version on the server.
正解：B,D
質問 5：
Click the exhibit button.
A customer reports that their system recently began logging an error.
Referring to the exhibit, which two statements are correct? (Choose two.)
A. A user is attempting to restart the ntpd daemon.
B. The ntpd daemon is responsible for time services.
C. The spmd application failed to restart the ntpd daemon.
D. The bcomd application is responsible for monitoring the observed behavior.
正解：A,B
質問 6：
A customer has created an interface group (igroup) named a0a, a VLAN named a0a-2500, and a data LIF associated with the VLAN interface that has been assigned an IP of 10.254.10.100. The customer is able to ping 10.254.10.100 from a Windows client without any issues, but data traffic is not working.
In this scenario, what is the solution to the problem?
A. Correct the MTU mismatch between the broadcast domain configuration and the upstream network switches.
B. Disable flow control on the a0a interface.
C. Allow data traffic by using LIF firewall policies.
D. Configure an appropriate service policy for the data LIF.
正解：C
0 お客様のコメント