1023 お客様のコメント
質問 1：
Exhibit:
A customer needs to change ports 0e and 0f on AFF_1 to support FC.
Referring to the exhibit, which three steps are required to accomplish this task? (Choose three.)
A. Reboot the node.
B. Issue the ucadmin modify -node AFF_1 -adapter 0e -mode FC -type initiator command.
C. Restart the FC service.
D. Take ports 0e and 0f offline.
E. Issue the ucadmin modify -node AFF_1 -adapter 0e -mode FC -type target command.
正解：B,C,D
質問 2：
You recently bought a FAS8200 series with SAS drives and want to maximize data efficiencies. Performance is not a primary Which two statements are correct in this scenario? (Choose two.)
A. Enable compression.
B. Enable always-on deduplication.
C. Enable always-on compaction.
D. Enable both inline and post process efficiencies.
正解：B,D
質問 3：
You have an SVM that serves LUNs to your hosts in an FC SAN environment. This SVM runs on a 4-node cluster and has two data LIFs on each node, according to best practices. You just created a LUN and mapped it to your initiators group. The LUN is owned by node01.
In this scenario, what would be an appropriate test for LUN mobility?
A. Copy the LUN to another node and create a new LUN map.
B. Move the LUN to node02.
C. Physically disconnect the SAN ports, and verify if the SAN data LIFs automatically move to other hosts.
D. Mirror the LUN to another node in your cluster.
正解：B
質問 4：
You use iSCSI to present a LUN to a newly installed Windows 2016 Server. You have created the volume and LUN on the NetApp cluster. When you perform a hardware rescan on the Windows host, you cannot see the newly presented storage.
What are three reasons for this problem? (Choose three.)
A. The volume has not been enabled for iSCSI access.
B. The protocol has not been enabled on the NetApp cluster.
C. The wrong igroup has been associated with the new LUN.
D. You need to add the IQN of the Windows host to the newly created LUN.
E. The IQN of the Windows host is not included in the igroup for the new LUN.
正解：B,C,D
質問 5：
You are configuring both NVMe and FC on the same AFF A700 2-node ONTAP 9.5 cluster. You are also configuring both protocols on the same FC fabric using the same A700 HBA ports.
In this scenario, which three configurations are supported? (Choose three.)
A. 8 GB HBAs
B. 16 GB fabrics
C. 16 GB HBAs
D. 32 GB HBAs
E. 32 GB fabrics
正解：A,B,D
質問 6：
You are planning to set up a new SAN with an AFF A300 2-node switchless cluster. Your SAN fabric will consist of Cisco MDS9148s switches.
According to NetApp best practices, which two actions would be required to accomplish this task? (Choose two.)
A. Set the switchport speed setting to 16 Gb.
B. Use multiple initiator, single target zoning.
C. Use single initiator, multiple target zoning.
D. Set the switchport speed to auto negotiate.
正解：C,D
解説: (Pass4Test メンバーにのみ表示されます)
質問 7：
You have a 4-node cluster with an AFF A300 HA pair and a FAS8200 HA pair. You plan on using the default storage efficiency settings. With inline data compaction, you estimate that you can save 6% of storage space. AFF A300 volumes that use under 5000 IOPS are moved to a FAS8200 using the volume move command.
In this scenario, what happens to the data after the volume is moved? (Choose two.)
A. The new written data is compacted.
B. The existing data is compacted.
C. The new written data is not compacted.
D. The existing data is not compacted.
正解：C
質問 8：
Exhibit:
You have a performance critical database application that is running on a FAS9000 controller that uses FC. As shown in the exhibit, volume efficiency is enabled.
If you follow the performance recommendation, what are two results to the data in the volume? (Choose two.)
A. The existing data is compressed.
B. The existing data is uncompressed.
C. The new written data is compressed.
D. The new written data is uncompressed.
正解：B,C
質問 9：
Exhibit:
An administrator has an AFF A200 HA pair.
Referring to the exhibit, how many 10 Gbps connections would the customer have on a single node for SAN host connectivity?
A. 4
B. 6
C. 7
D. 2
正解：A
Exhibit:
A customer needs to change ports 0e and 0f on AFF_1 to support FC.
Referring to the exhibit, which three steps are required to accomplish this task? (Choose three.)
A. Reboot the node.
B. Issue the ucadmin modify -node AFF_1 -adapter 0e -mode FC -type initiator command.
C. Restart the FC service.
D. Take ports 0e and 0f offline.
E. Issue the ucadmin modify -node AFF_1 -adapter 0e -mode FC -type target command.
正解：B,C,D
質問 2：
You recently bought a FAS8200 series with SAS drives and want to maximize data efficiencies. Performance is not a primary Which two statements are correct in this scenario? (Choose two.)
A. Enable compression.
B. Enable always-on deduplication.
C. Enable always-on compaction.
D. Enable both inline and post process efficiencies.
正解：B,D
質問 3：
You have an SVM that serves LUNs to your hosts in an FC SAN environment. This SVM runs on a 4-node cluster and has two data LIFs on each node, according to best practices. You just created a LUN and mapped it to your initiators group. The LUN is owned by node01.
In this scenario, what would be an appropriate test for LUN mobility?
A. Copy the LUN to another node and create a new LUN map.
B. Move the LUN to node02.
C. Physically disconnect the SAN ports, and verify if the SAN data LIFs automatically move to other hosts.
D. Mirror the LUN to another node in your cluster.
正解：B
質問 4：
You use iSCSI to present a LUN to a newly installed Windows 2016 Server. You have created the volume and LUN on the NetApp cluster. When you perform a hardware rescan on the Windows host, you cannot see the newly presented storage.
What are three reasons for this problem? (Choose three.)
A. The volume has not been enabled for iSCSI access.
B. The protocol has not been enabled on the NetApp cluster.
C. The wrong igroup has been associated with the new LUN.
D. You need to add the IQN of the Windows host to the newly created LUN.
E. The IQN of the Windows host is not included in the igroup for the new LUN.
正解：B,C,D
質問 5：
You are configuring both NVMe and FC on the same AFF A700 2-node ONTAP 9.5 cluster. You are also configuring both protocols on the same FC fabric using the same A700 HBA ports.
In this scenario, which three configurations are supported? (Choose three.)
A. 8 GB HBAs
B. 16 GB fabrics
C. 16 GB HBAs
D. 32 GB HBAs
E. 32 GB fabrics
正解：A,B,D
質問 6：
You are planning to set up a new SAN with an AFF A300 2-node switchless cluster. Your SAN fabric will consist of Cisco MDS9148s switches.
According to NetApp best practices, which two actions would be required to accomplish this task? (Choose two.)
A. Set the switchport speed setting to 16 Gb.
B. Use multiple initiator, single target zoning.
C. Use single initiator, multiple target zoning.
D. Set the switchport speed to auto negotiate.
正解：C,D
解説: (Pass4Test メンバーにのみ表示されます)
質問 7：
You have a 4-node cluster with an AFF A300 HA pair and a FAS8200 HA pair. You plan on using the default storage efficiency settings. With inline data compaction, you estimate that you can save 6% of storage space. AFF A300 volumes that use under 5000 IOPS are moved to a FAS8200 using the volume move command.
In this scenario, what happens to the data after the volume is moved? (Choose two.)
A. The new written data is compacted.
B. The existing data is compacted.
C. The new written data is not compacted.
D. The existing data is not compacted.
正解：C
質問 8：
Exhibit:
You have a performance critical database application that is running on a FAS9000 controller that uses FC. As shown in the exhibit, volume efficiency is enabled.
If you follow the performance recommendation, what are two results to the data in the volume? (Choose two.)
A. The existing data is compressed.
B. The existing data is uncompressed.
C. The new written data is compressed.
D. The new written data is uncompressed.
正解：B,C
質問 9：
Exhibit:
An administrator has an AFF A200 HA pair.
Referring to the exhibit, how many 10 Gbps connections would the customer have on a single node for SAN host connectivity?
A. 4
B. 6
C. 7
D. 2
正解：A
Yoshida -
Pass4TestのNS0-509問題集は実際の試験問題に非常に似ており、実践しながらの練習ができました。本番でも実力が発揮出来合格しました。どうもありがとうございました。