質問 1：
You install a new AFF A300 2-node switchless cluster with ONTAP 9.1 at a customer site. Each node has a root aggregate as part of the system configuration.
In this scenario, what is the default disk partitioning called?
A. data-data partitioning
B. root-data-data partitioning
C. root-data-root partitioning
D. root-data partitioning
正解：D
質問 2：
Click the Exhibit button.
While planning for an installation, you download ONTAP 9.1 as requested by the customer. As you begin the installation, you determine that the system shipped with ONTAP 9.0 software installed. Because of this, you boot to the Special Boot Menu shown in the exhibit.
What should you use to upgrade the ONTAP software on the customer's cluster?
A. Use option 5, "Maintenance mode boot", and then use the system node image update command to upgrade to ONTAP 9.1 software.
B. Use option 6, "Update flash from backup config" to upgrade to ONTAP 9.1 software.
C. Use option 7, "Install new software first," to upgrade to ONTAP 9.1 software.
D. Use option 5, "Maintenance mode boot," and then use the software update command to upgrade to ONTAP 9.1 software.
正解：B
質問 3：
You have a 2-node switchless cluster named clusterA. You are planning on adding two additional nodes to clusterA.
What must you consider before you add the addiHonal nodes to clusterA?
A. Convert clusterA to a switch** cluster by migrating the cluster LIFs from direct connect to the cluster interconnect switch.
B. Convert clusterA to a single-node cluster.
C. Use direct connect to add the additional nodes to clusterA.
D. Convert clusterA to a switched cluster by migrating the data lIFs from direct connect to die cluster interconnect switch.
正解：A
質問 4：
A new AFF8200 has a four-port UTA2 adapter installed in slot 2. Using the ucadmin command, you see that these ports are configured for FC.
Which port names are correct in this scenario?
A. e0a/0a, e0b/0b, e0c/0c, e0d/od
B. 2a, 2b, 2c, 2d
C. e2a, e2b, e2c, e2d
D. e2a/2a, e2b/2b, e2c/2c, e2d/2d
正解：B
質問 5：
Select the Exhibit tab.
Your customer has an AFF A300 installed. They ask you to configure the e0a and e0b ports to use the FC protocol.
Referring to the exhibit, which statement is correct in this scenario?
A. These ports are used for the cluster interconnect.
B. These ports are used for the Ethernet uplink into the customer's network.
C. The configuration of these ports can only be done by OnCommand System Manager.
D. Use the ucadmin command to configure these ports as FC ports.
正解：A
質問 6：
You want to expand an existing FAS8060 switchless cluster running ONTAP 9.1 with an AFF A300 system.
Which action should you take to perform this task?
A. Create a separate switchless cluster with the AFF A300 system.
B. Add and configure the cluster interconnect switches, re-cable the FAS8060 cluster, add the AFF A300 system, and join the existing cluster.
C. Connect the cluster ports of the AFF A300 system to the existing FAS8060 cluster, and join the existing cluster.
D. Execute the cluster setup command on the existing FAS8060 cluster, add the cluster interconnect switches, and cable both the FAS8060 cluster and the AFF A300 system to the new cluster.
正解：C
質問 7：
Config Advisor reports that you have a single point of failure on a stack of shelves. After investigation, you have assigned the following ports to each stack:
stack 1 - ports 0a and 0b
stack 2 -ports 3a and 4b
stack 3 - ports 4a and 3b
In this scenario, which two changes would you make to the cabling to solve the problem? (Choose two.)
A. Cable stack 2 to ports 4a and 4b.
B. Cable stack 1 to ports 0a and 3b.
C. Cable stack 3 to ports 4a and 0b.
D. Cable stack 3 to ports 3a and 3b.
正解：A,B
質問 8：
What is a valid failover policy for a SAN LIF?
A. disabled
B. broadcast-domain-wide
C. local-only
D. system-define
正解：B
You install a new AFF A300 2-node switchless cluster with ONTAP 9.1 at a customer site. Each node has a root aggregate as part of the system configuration.
In this scenario, what is the default disk partitioning called?
A. data-data partitioning
B. root-data-data partitioning
C. root-data-root partitioning
D. root-data partitioning
正解：D
質問 2：
Click the Exhibit button.
While planning for an installation, you download ONTAP 9.1 as requested by the customer. As you begin the installation, you determine that the system shipped with ONTAP 9.0 software installed. Because of this, you boot to the Special Boot Menu shown in the exhibit.
What should you use to upgrade the ONTAP software on the customer's cluster?
A. Use option 5, "Maintenance mode boot", and then use the system node image update command to upgrade to ONTAP 9.1 software.
B. Use option 6, "Update flash from backup config" to upgrade to ONTAP 9.1 software.
C. Use option 7, "Install new software first," to upgrade to ONTAP 9.1 software.
D. Use option 5, "Maintenance mode boot," and then use the software update command to upgrade to ONTAP 9.1 software.
正解：B
質問 3：
You have a 2-node switchless cluster named clusterA. You are planning on adding two additional nodes to clusterA.
What must you consider before you add the addiHonal nodes to clusterA?
A. Convert clusterA to a switch** cluster by migrating the cluster LIFs from direct connect to the cluster interconnect switch.
B. Convert clusterA to a single-node cluster.
C. Use direct connect to add the additional nodes to clusterA.
D. Convert clusterA to a switched cluster by migrating the data lIFs from direct connect to die cluster interconnect switch.
正解：A
質問 4：
A new AFF8200 has a four-port UTA2 adapter installed in slot 2. Using the ucadmin command, you see that these ports are configured for FC.
Which port names are correct in this scenario?
A. e0a/0a, e0b/0b, e0c/0c, e0d/od
B. 2a, 2b, 2c, 2d
C. e2a, e2b, e2c, e2d
D. e2a/2a, e2b/2b, e2c/2c, e2d/2d
正解：B
質問 5：
Select the Exhibit tab.
Your customer has an AFF A300 installed. They ask you to configure the e0a and e0b ports to use the FC protocol.
Referring to the exhibit, which statement is correct in this scenario?
A. These ports are used for the cluster interconnect.
B. These ports are used for the Ethernet uplink into the customer's network.
C. The configuration of these ports can only be done by OnCommand System Manager.
D. Use the ucadmin command to configure these ports as FC ports.
正解：A
質問 6：
You want to expand an existing FAS8060 switchless cluster running ONTAP 9.1 with an AFF A300 system.
Which action should you take to perform this task?
A. Create a separate switchless cluster with the AFF A300 system.
B. Add and configure the cluster interconnect switches, re-cable the FAS8060 cluster, add the AFF A300 system, and join the existing cluster.
C. Connect the cluster ports of the AFF A300 system to the existing FAS8060 cluster, and join the existing cluster.
D. Execute the cluster setup command on the existing FAS8060 cluster, add the cluster interconnect switches, and cable both the FAS8060 cluster and the AFF A300 system to the new cluster.
正解：C
質問 7：
Config Advisor reports that you have a single point of failure on a stack of shelves. After investigation, you have assigned the following ports to each stack:
stack 1 - ports 0a and 0b
stack 2 -ports 3a and 4b
stack 3 - ports 4a and 3b
In this scenario, which two changes would you make to the cabling to solve the problem? (Choose two.)
A. Cable stack 2 to ports 4a and 4b.
B. Cable stack 1 to ports 0a and 3b.
C. Cable stack 3 to ports 4a and 0b.
D. Cable stack 3 to ports 3a and 3b.
正解：A,B
質問 8：
What is a valid failover policy for a SAN LIF?
A. disabled
B. broadcast-domain-wide
C. local-only
D. system-define
正解：B
0 お客様のコメント