971 お客様のコメント
質問 1：
A server has two power supply units (PSUs) in a redundant configuration. One power supply unit fails.
A technician replaces the failed PSU, but the server does NOT return to redundant power mode.
What is the cause of this issue?
A. The power redundant options is disabled in the System Setup Utility.
B. Both PSUs were NOT replaced at the same time.
C. The server has NOT been Power Cycles to bring the new PSU online.
D. The new PSU has a different wattage than the existing PSU.
正解：A
質問 2：
A technician is updating firmware on a Windows Server using the Lifecycle Controller following a NIC replacement, but it fails to complete the update on the NIC despite successfully updating other components.
The update's readme confirms that the current version is too old to upgrade with the Lifecycle Controller and an alternative method must be used.
Which three update methods could the technician use to meet this requirement? (Choose three.)
A. Launch Server Update Utility (SUU) from the OS
B. Use Update and Rollback within the iDRAC web GUI
C. Create a bootable ISO file with Repository Manager
D. Launch Platform Update from OpenManage Server Administrator
E. Run a Dell Update Package (DUP) from the OS
正解：C,D,E
質問 3：
A technician installs a server with a network daughter card (NDC). The NDC has two 10Gb BaseT ports as well as 1Gb BaseT ports. The technician is using the correct CAT-6 network cable and a 10Gb switch.
The server reports 1Gb connections on ports 3 and 4. Ports 1 and 2 are down.
How should the technician get 10Gb connectivity?
A. Move the cables over to ports 1 and 2
B. Use different ports on the switch
C. Hard set the switch ports to 10Gb
D. Replace the network cables
正解：B
質問 4：
A server needs to be configured with a six disk RAID 10 using 3 TB drives.
What should be the available array size in this configuration?
A. 9TB
B. 6TB
C. 4TB
D. 12TB
正解：A
質問 5：
A technician wants to upgrade the iDRAC license from Express to Enterprise.
What are the three methods the technician can use to install the new license? (Choose three.)
A. SSH in the iDRAC and use a RACADM command to import the new license.
B. Boot F10 to the Lifecycle Controller and import the license.
C. Load the iDRAC GUI mid import the new license.
D. SSH into the iDRAC and use WSMAN to import the new license.
E. Boot F2 and import the iDRAC license.
正解：A,B,E
質問 6：
A technician installs OpenManage Server Administrator (OMSA) on a server.
Which two address options should be used to access OMSA remotely using a web browser? (Choose two.)
A. https://IP address : 80
B. https://IP address : 443
C. https://IP address : 2607
D. https://hostname : 1311
E. https://hostname : 2607
F. https://IP address : 1311
正解：B,C,E
A server has two power supply units (PSUs) in a redundant configuration. One power supply unit fails.
A technician replaces the failed PSU, but the server does NOT return to redundant power mode.
What is the cause of this issue?
A. The power redundant options is disabled in the System Setup Utility.
B. Both PSUs were NOT replaced at the same time.
C. The server has NOT been Power Cycles to bring the new PSU online.
D. The new PSU has a different wattage than the existing PSU.
正解：A
質問 2：
A technician is updating firmware on a Windows Server using the Lifecycle Controller following a NIC replacement, but it fails to complete the update on the NIC despite successfully updating other components.
The update's readme confirms that the current version is too old to upgrade with the Lifecycle Controller and an alternative method must be used.
Which three update methods could the technician use to meet this requirement? (Choose three.)
A. Launch Server Update Utility (SUU) from the OS
B. Use Update and Rollback within the iDRAC web GUI
C. Create a bootable ISO file with Repository Manager
D. Launch Platform Update from OpenManage Server Administrator
E. Run a Dell Update Package (DUP) from the OS
正解：C,D,E
質問 3：
A technician installs a server with a network daughter card (NDC). The NDC has two 10Gb BaseT ports as well as 1Gb BaseT ports. The technician is using the correct CAT-6 network cable and a 10Gb switch.
The server reports 1Gb connections on ports 3 and 4. Ports 1 and 2 are down.
How should the technician get 10Gb connectivity?
A. Move the cables over to ports 1 and 2
B. Use different ports on the switch
C. Hard set the switch ports to 10Gb
D. Replace the network cables
正解：B
質問 4：
A server needs to be configured with a six disk RAID 10 using 3 TB drives.
What should be the available array size in this configuration?
A. 9TB
B. 6TB
C. 4TB
D. 12TB
正解：A
質問 5：
A technician wants to upgrade the iDRAC license from Express to Enterprise.
What are the three methods the technician can use to install the new license? (Choose three.)
A. SSH in the iDRAC and use a RACADM command to import the new license.
B. Boot F10 to the Lifecycle Controller and import the license.
C. Load the iDRAC GUI mid import the new license.
D. SSH into the iDRAC and use WSMAN to import the new license.
E. Boot F2 and import the iDRAC license.
正解：A,B,E
質問 6：
A technician installs OpenManage Server Administrator (OMSA) on a server.
Which two address options should be used to access OMSA remotely using a web browser? (Choose two.)
A. https://IP address : 80
B. https://IP address : 443
C. https://IP address : 2607
D. https://hostname : 1311
E. https://hostname : 2607
F. https://IP address : 1311
正解：B,C,E
田村** -
Dellさんの問題集は解説が丁寧で理解が助かります。DCAPE-100本番試験に無事合格いたしました。