最新なAvaya 7004.1問題集（66題）、真実試験の問題を全部にカバー！

質問 1：
When configuring Zone Based Dialing, what option would you select to create new zones for routing calls through a centralized Call Server?
A. Numbering Zones link
B. Bandwidth Zones link
C. Dialing Configuration Details for Flexible Dial Plan link
D. Dialing Configuration Details link
正解：C

質問 2：
Click the Exhibit button.

A customer's dialing requirement, listed below, require that all station users assigned an NCOS of 3 and Class of Service of Conditionally Toll Denied (CTD) be able to place toll calls from the United States to Australia.
Australia Country Code: 61
NCOS of 3 has an FRL of 3
Expensive Routers are not being used
With reference to the exhibit, which table will allow all station users to be able to place these toll calls?
A. Provisioning Table B
B. Provisioning Table C
C. Provisioning Table A
D. Provisioning Table D
正解：A

質問 3：
When attempting to program Zone Based Dialing through Element Manager, the user is unable to access the Dialing Configuration Page.
What needs to be configured before the Dialing Configuration Page can be accessed, assuming the ZBN_PACKAGE (420) is already installed?
A. The ZBN_PACKAGE (420) needs to be disabled.
B. The CDP dialing plan needs to be programmed.
C. Nothing, Zone Based Dialing cannot be configured in Element Manger.
D. Number Zones need to be configured
正解：D

質問 4：
Your customer has a Communication Server 1000 RIs. 7 x system equipped with System Errors and Events Lookup pack 245 that provides the ability to display system messages on screen.
When a system message in received, which procedure should you use to look it up and display it on the screen?
A. Enter errcde followed by the system error code and <cr>. For example, errcde bug4080<cr>
B. Enter bug followed by the system error code and <cr>. For example, bugerr4080<cr>
C. Enter the system error number followed by <cr> For example, bug4080<cr>
D. Enter err followed by the system error code followed by <cr>. For example, err bug4080<cr>
正解：B
解説: (Pass4Test メンバーにのみ表示されます)

質問 5：
Click the Exhibit button.

A customer has asked if the Communication Server 1000 RIs. 7 x system can route anyone that dial an unassigned number in the customer's DID range to the Attendant.
In reviewing the current configuration as shown in the exhibit, what do you conclude?
(Choose two)
A. NET_DATA Attendant and tie trunk users are receiving an overflow tone
B. internal station users and non tie line users are routing to the Attendant
C. all caller types are receiving an overflow tone
D. only internal station users are routing to the Attendant
正解：B

質問 6：
Click the Exhibit button.


Given a customer's Coordinating Dialing Plan shown in the exhibit, if a Station user at CDP Switch #2 dials 327-3249, which route list used and where will the call terminate?
A. Route List 10 will be utilized and the call will terminate at CDP Switch #3
B. Route List 2 will be utilized and the call will terminate at CDP Switch #2
C. Route List 1 will be utilized and the call will terminate at CDP Switch #3
D. Route List 5 will be utilized and the call will terminate at CDP Switch #2
正解：B

質問 7：
Given the following network characteristics:
three Communication Server 1000 RIs. 7 x systems IP Peer Networking required DN uniqueness cannot be maintained route calls using site Location Codes (LOCs)
Which type of dialing plan is recommended for this call routing scenario?
A. Coordinated Dialing Plan (CDP)
B. Uniform Dialing Plan (UDP)
C. Flexible Numbering Plan (FNP)
D. Network Attendant Numbering Plan
正解：C