1229 お客様のコメント
質問 1：
Which NetApp resource would you use to validate the maximum number of FC hops that are supported by a switch vendor?
A. Installation and Setup Instructions Poster
B. Switch Install Guide
C. Hardware Universe
D. SAN Configuration Guide
正解：D
質問 2：
A company has Snapmirror configured between two ONTAP clusters. They want to add nodes to one of the clusters at a minimum, which LIF would be required to be defined on the new nodes?
A. Node-management
B. Data, node-management, and FC
C. Node-management and intercluster
D. Node-management, data, and intercluster
正解：B
質問 3：
You want to create a thick provisioned LUN within a thick-provisioned volume.
Which 2 actions will accomplish this task? (Choose two.)
A. Use the lun create command with the space-reserve parameter set to enabled
B. Use the lun create command with the space-reserve parameter set to disabled
C. Use the vol create command with a guarantee parameter set to volume
D. Use the vol create command with a guarantee parameter set to none
正解：A,C
質問 4：
Where do you identify the disk shelves and disks that are supported for a specific controller model?
A. Installation and Setup Instructions poster
B. Disk and Aggregates Power guide
C. Interoperability Matrix Tool (IMT)
D. Hardware Universe (HWU)
正解：D
質問 5：
You are asked to configure the Service Processor on a newly installed node, and must verify the following command:
system-service processor network modify -node local -address-family IPv4 -enable true - ip-address 192.168.123.98 -netmask 255.255.255.0
Which statement about this command is true?
A. The gateway IP address is missing.
B. -nodeshould reference the actual node name.
C. IPv6 is required for the SP.
D. The Link Local IP Address is missing.
正解：A,B
質問 6：
You want to ensure maximum performance of iSCSI LUNs.
Which statement is correct in this scenario?
A. Use 1GbE instead of 1OGbE.
B. Configure your network to have Layer 3 switches.
C. Set the MTU size to 9000.
D. Enable flow control on the switch.
正解：C
質問 7：
A storage administrator wants to ensure multipathing between the initiator and the target.
The current connection uses target portal group 1027.
Referring to the exhibit, which IP address should be used to accomplish this task?
A. 192.168.0.167
B. 192.168.0.165
C. 192.168.0.53
D. 192.168.0.166
正解：D
質問 8：
An Administrator has an ONTAP 9.1 cluster. The cluster contains a number of volumes with data writes as shown in the exhibit. Adaptive compression is enabled, and the initial space savings that are shown are achieved. The administrator has enabled data compaction on the volumes.
Referring to the exhibit. How many ONTAP blocks would be used to hold the data after data compaction is enabled?
A. 8
B. 11
C. 10
D. 6
正解：A
Which NetApp resource would you use to validate the maximum number of FC hops that are supported by a switch vendor?
A. Installation and Setup Instructions Poster
B. Switch Install Guide
C. Hardware Universe
D. SAN Configuration Guide
正解：D
質問 2：
A company has Snapmirror configured between two ONTAP clusters. They want to add nodes to one of the clusters at a minimum, which LIF would be required to be defined on the new nodes?
A. Node-management
B. Data, node-management, and FC
C. Node-management and intercluster
D. Node-management, data, and intercluster
正解：B
質問 3：
You want to create a thick provisioned LUN within a thick-provisioned volume.
Which 2 actions will accomplish this task? (Choose two.)
A. Use the lun create command with the space-reserve parameter set to enabled
B. Use the lun create command with the space-reserve parameter set to disabled
C. Use the vol create command with a guarantee parameter set to volume
D. Use the vol create command with a guarantee parameter set to none
正解：A,C
質問 4：
Where do you identify the disk shelves and disks that are supported for a specific controller model?
A. Installation and Setup Instructions poster
B. Disk and Aggregates Power guide
C. Interoperability Matrix Tool (IMT)
D. Hardware Universe (HWU)
正解：D
質問 5：
You are asked to configure the Service Processor on a newly installed node, and must verify the following command:
system-service processor network modify -node local -address-family IPv4 -enable true - ip-address 192.168.123.98 -netmask 255.255.255.0
Which statement about this command is true?
A. The gateway IP address is missing.
B. -nodeshould reference the actual node name.
C. IPv6 is required for the SP.
D. The Link Local IP Address is missing.
正解：A,B
質問 6：
You want to ensure maximum performance of iSCSI LUNs.
Which statement is correct in this scenario?
A. Use 1GbE instead of 1OGbE.
B. Configure your network to have Layer 3 switches.
C. Set the MTU size to 9000.
D. Enable flow control on the switch.
正解：C
質問 7：
A storage administrator wants to ensure multipathing between the initiator and the target.
The current connection uses target portal group 1027.
Referring to the exhibit, which IP address should be used to accomplish this task?
A. 192.168.0.167
B. 192.168.0.165
C. 192.168.0.53
D. 192.168.0.166
正解：D
質問 8：
An Administrator has an ONTAP 9.1 cluster. The cluster contains a number of volumes with data writes as shown in the exhibit. Adaptive compression is enabled, and the initial space savings that are shown are achieved. The administrator has enabled data compaction on the volumes.
Referring to the exhibit. How many ONTAP blocks would be used to hold the data after data compaction is enabled?
A. 8
B. 11
C. 10
D. 6
正解：A
原田** -
Pass4TestのNS0-507問題集は「わかりやすさ」「見やすさ」「網羅性」という加点ポイントがあって受かないわけがないよ。