Messages are building up on a transmission queue. The administrator issues the following command: DIS CHSTATUS(QM1.TO.QM2) ALL. What output can the administrator use determine the cause
A. A higher than expected RVCRTIME vaLue couLd indicate the receiver is taking too long before acknowLedging the message
B. A higher than expected NETTIME couLd indicate too much time across the network
C. A higher than expected PROCTIME vaLue couLd indicate the message is taking too Long to get through the exits
D. A higher than expected COMTIME value couLd indicate too much time setting up comrninications
正解:B
質問 2:
An administrator has setup a muLti-instance queue manager QMI. A JMS appLication using IBM MQ classes is connecting to the active Instance of this muLti-Instance Implementation. What value should the administrator set for CLIENTRECONNECTOPTIONS property of connection factory, so that the application automaticaLLy reconnects to standby queue manager if primary queue manager goes down.
A. HA
B. ALL
C. MULTI
D. QMGR
正解:D
質問 3:
Which security option can an administrator implement to secure the connection between MQ Explorer and the remote queue manager?
A. Configure the SCYEXIT property on the SERVER channeL
B. Configure the MSGEXIT property on the SVRCONN channel
C. Configure a non-blank MCA USER vaLue on the SERVER channeL
D. Configure the SCYEXIT property on the SVRCONN channel
正解:D
質問 4:
Two queue managers TESTQMGRI and TESTQMGR2 are connected using sender receiver channels on both sides.
An application sends messages on TEST.REMOTE of TESTQMGRI destined for queue NEW.LOCAL on TESTQMGR2.
The administrator has been asked to ensure that if messages from TESTQMGRI destined for NEW.LOCAL end up on the dead letter queue, they need to sent back to a queue TEST.LOCAL on TESTQMGRI. Which rule does the administrator need
to set In the dead letter handler rule table to achieve this objective?
A. REASON(*)ACTION(FWD)FWDQ(&RPLYQ)FWDQM(&REPLYQM)HEADER(NO)DEST(NEW.LOCAL)
B. REASON(*)ACTION(FWD)FWD(&DEST)FWDQM(&DESTQM)HEADER(NO)
C. REASON(*)ACTION(FWD)FWDQ(TEST.LOCAL)FWDQM(&DESTQM)HEADER(NO)
D. REASON(*)ACTION(FWD)FWD?TEST.LOCAL)FWDQM(&REPLYQM)HEADER(NO)DEST(NEW.LOCAL)
正解:D
質問 5:
The foLlowing commands are issued on QMGRA:
DEFINE QLOCAL(SATURN)
DEFINE QLOCAL(QMGRB) USAGE(XMIT)
DEFINE QALIAS(MARS) TARGET( VENUS)
DEFINE QALIAS(PLUTO) TARGET(SATURN)
DEFINE QREMOTE(VENUS) RNAME(SATURN) RQMNAME(QMGRB)
The following commands are issued on QMGRB:
DEFINE QLOCAL(MARS)
DEFINE QLOCAL(QMGRA) USAGE(XMITQ)
DEFINE QALIAS(SATURN) TARGET(MARS)
DEFINE QALIAS(PLUTO) TARGET( VENUS)
DEFINE QREMOTE(VENUS) RNAME(PLUTO) RQMNAME(QMGRA)
Where does the message go when It Is put to MARS on QMGRA?
A. MARS on QMGRB
B. SATURN on QMGRB
C. SATURN on QGRA
D. MARS on QMGRA
正解:A
質問 6:
Which two SSL/TLS configuration choices can impact performance or certificate processing?
A. DepLoying CA-signed certificates within seLf-signed certificates
B. Using self-signed certificates that have expired
C. ALlowing mutipLe certificates on the same queue manager
0: More than 100 certificates stored within the key repository
D. ExplicitLy vaLidating RFC5280 policy ruLes
正解:A,D