747 お客様のコメント
質問 1：
An administrator is configuring a new virtual Fibre Channel connection that will use NPIV to connect a client LPAR to a SAN.
The administrator has created a client adapter in virtual slot 8 and a server adapter in virtual slot 600. The appropriate virtual adapter definitions have been successfully added into the client and VIO server profiles and a DLPAR operation to add the virtual adapters into both partitions.
The administrator runs cfgmgr on the client partition but receives an error. The administrator then checks the definition of the client adapter in AIX Based on this information, what is the most likely cause of the error?
A. The virtual server adapter has been incorrectly mapped to virtual slot 3 for the client.
B. The virtual Fibre Channel device driver has not been installed on the client.
C. The virtual server adapter has not been mapped to a physical Fibre Channel adapter.
D. The virtual Fibre Channel server adapters are not supported with virtual slot numbers higher than 512.
正解：C
質問 2：
During a Live Partition Mobility action, the network on one of the MSPs fails and an error is shown. Checking the HMC, the administrator sees the following:
What is the current state of the source LPAR?
A. Running but inaccessible via network
B. Running but in a restricted state
C. Running and accessible as normal
D. Running but with read-only SAN connectivity
正解：C
質問 3：
An administrator adds a new virtual target device to a vhost adapter that already had target devices on it. The client LPAR does not detect the new disk and the following error has been logged in the errlog:
What is the most likely cause for this situation?
A. The queue_depth parameter of the new drive is larger than those of the other drives provided by the host adapter
B. The intr_lsi of the host adapter is set higher than that needed by the new drive
C. The max_transfer parameter of the new drive is smaller than the rate already reported by the host adapter
D. The intr_priority of the host adapter is set lower than that needed by the new drive.
正解：C
質問 4：
An administrator has a Power 720 with 64GB of memory and Active Memory Expansion (AME).
An LPAR has only 10GB of memory available and an application has been sized at 15GB of memory. The administrator runs amepat to determine an efficient expansion factor. Based on the output, an expansion factor of 1.6 has been chosen.
How should this be configured in the LPAR?
A. Enter 10GB as 'desired', enter 1.6 in the Active memory expansion factor field.
B. Enter 16GB as 'desired' and modify/etc/ame.conf with AME_RATIO=1.6.
C. Enter 16GB as 'desired', enter 1.6 in the Active memory expansion factor field.
D. Enter 10GB as 'desired' and modify/etc/ame.conf with AME_RATIO=1.6.
正解：A
質問 5：
An architect is planning to use an existing NIM server to back up and restore VIO server partitions. In addition to the backup of the VIO Server (VIOS), what is needed to successfully complete a restore operation?
A. A copy of the VIOS bosinst. data from the VIOS partition.
B. A copy of the volume group structures and a list of device mappings from the VIOS partition.
C. A backup of the profile data from the VIOS partition.
D. A valid LPP Source on the NIM partition and an extracted SPOT from the VIOS backup.
正解：B
質問 6：
Which of the following statements regarding the implementation of Multiple Shared Processor Pools (MSPPs) is correct?
A. MSPPs allow the restriction of transferring available processor cycles from one set of LPARs to another.
B. MSPPs allow for physical sets of processors to be reserved for specific sets of LPARs.
C. MSPPs allow for both IBM and third party applications to be licensed for a subset of physical processors.
D. MSPPs allow processor capacity consumption to be restricted to a set of LPARs.
正解：D
An administrator is configuring a new virtual Fibre Channel connection that will use NPIV to connect a client LPAR to a SAN.
The administrator has created a client adapter in virtual slot 8 and a server adapter in virtual slot 600. The appropriate virtual adapter definitions have been successfully added into the client and VIO server profiles and a DLPAR operation to add the virtual adapters into both partitions.
The administrator runs cfgmgr on the client partition but receives an error. The administrator then checks the definition of the client adapter in AIX Based on this information, what is the most likely cause of the error?
A. The virtual server adapter has been incorrectly mapped to virtual slot 3 for the client.
B. The virtual Fibre Channel device driver has not been installed on the client.
C. The virtual server adapter has not been mapped to a physical Fibre Channel adapter.
D. The virtual Fibre Channel server adapters are not supported with virtual slot numbers higher than 512.
正解：C
質問 2：
During a Live Partition Mobility action, the network on one of the MSPs fails and an error is shown. Checking the HMC, the administrator sees the following:
What is the current state of the source LPAR?
A. Running but inaccessible via network
B. Running but in a restricted state
C. Running and accessible as normal
D. Running but with read-only SAN connectivity
正解：C
質問 3：
An administrator adds a new virtual target device to a vhost adapter that already had target devices on it. The client LPAR does not detect the new disk and the following error has been logged in the errlog:
What is the most likely cause for this situation?
A. The queue_depth parameter of the new drive is larger than those of the other drives provided by the host adapter
B. The intr_lsi of the host adapter is set higher than that needed by the new drive
C. The max_transfer parameter of the new drive is smaller than the rate already reported by the host adapter
D. The intr_priority of the host adapter is set lower than that needed by the new drive.
正解：C
質問 4：
An administrator has a Power 720 with 64GB of memory and Active Memory Expansion (AME).
An LPAR has only 10GB of memory available and an application has been sized at 15GB of memory. The administrator runs amepat to determine an efficient expansion factor. Based on the output, an expansion factor of 1.6 has been chosen.
How should this be configured in the LPAR?
A. Enter 10GB as 'desired', enter 1.6 in the Active memory expansion factor field.
B. Enter 16GB as 'desired' and modify/etc/ame.conf with AME_RATIO=1.6.
C. Enter 16GB as 'desired', enter 1.6 in the Active memory expansion factor field.
D. Enter 10GB as 'desired' and modify/etc/ame.conf with AME_RATIO=1.6.
正解：A
質問 5：
An architect is planning to use an existing NIM server to back up and restore VIO server partitions. In addition to the backup of the VIO Server (VIOS), what is needed to successfully complete a restore operation?
A. A copy of the VIOS bosinst. data from the VIOS partition.
B. A copy of the volume group structures and a list of device mappings from the VIOS partition.
C. A backup of the profile data from the VIOS partition.
D. A valid LPP Source on the NIM partition and an extracted SPOT from the VIOS backup.
正解：B
質問 6：
Which of the following statements regarding the implementation of Multiple Shared Processor Pools (MSPPs) is correct?
A. MSPPs allow the restriction of transferring available processor cycles from one set of LPARs to another.
B. MSPPs allow for physical sets of processors to be reserved for specific sets of LPARs.
C. MSPPs allow for both IBM and third party applications to be licensed for a subset of physical processors.
D. MSPPs allow processor capacity consumption to be restricted to a set of LPARs.
正解：D
森田** -
Pass4Testの問題集を購入して合格するのはこれで三回目になります。