581 お客様のコメント
クリック」
質問 1：
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
A. Use the job specification as a guide
B. Call the person who wrote the specification for clarification
C. Use the product data sheet as a guide
D. Call the coating manufacturer for clarification
正解：A
質問 2：
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
A. Shut the job down
B. Permit coating to take place so as not to lose the blast
C. Review the relevant standard with the Contractor
D. Call your supervisor
正解：C
質問 3：
The Inspector's Log Book is generally:
A. Shared with all parties upon project completion
B. Shredded by the inspector upon project completion
C. Submitted to the client upon project completion
D. Retained by the inspector upon project completion
正解：D
質問 4：
Which of these tests uses a syringe?
A. Potassium ferricyanide
B. Soluble salts meter
C. Sleeve test
D. Bresle patch
正解：D
質問 5：
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
A. Rust Grades A-D
B. Rust Grades 1-4
C. Surface Condition H
D. Surface Conditions E-G
正解：A
質問 6：
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
A. Yes, because the 'two standards are not equivalent
B. It depends on which hand tool the Contractor selects
C. It depends on which power tool the Contractor selects
D. No, because there is no real difference in the standards
正解：D
質問 7：
Check abrasive blast pressure close to the
A. substrate
B. compressor
C. blast nozzle
D. blast pot
正解：C
質問 8：
Fine cracks in the surface of a coating that rarely reach the substrate are called
A. cracking.
B. checking.
C. alligatoring.
D. blistering.
正解：B
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
A. Use the job specification as a guide
B. Call the person who wrote the specification for clarification
C. Use the product data sheet as a guide
D. Call the coating manufacturer for clarification
正解：A
質問 2：
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
A. Shut the job down
B. Permit coating to take place so as not to lose the blast
C. Review the relevant standard with the Contractor
D. Call your supervisor
正解：C
質問 3：
The Inspector's Log Book is generally:
A. Shared with all parties upon project completion
B. Shredded by the inspector upon project completion
C. Submitted to the client upon project completion
D. Retained by the inspector upon project completion
正解：D
質問 4：
Which of these tests uses a syringe?
A. Potassium ferricyanide
B. Soluble salts meter
C. Sleeve test
D. Bresle patch
正解：D
質問 5：
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
A. Rust Grades A-D
B. Rust Grades 1-4
C. Surface Condition H
D. Surface Conditions E-G
正解：A
質問 6：
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
A. Yes, because the 'two standards are not equivalent
B. It depends on which hand tool the Contractor selects
C. It depends on which power tool the Contractor selects
D. No, because there is no real difference in the standards
正解：D
質問 7：
Check abrasive blast pressure close to the
A. substrate
B. compressor
C. blast nozzle
D. blast pot
正解：C
質問 8：
Fine cracks in the surface of a coating that rarely reach the substrate are called
A. cracking.
B. checking.
C. alligatoring.
D. blistering.
正解：B
内田** -
NACE-CIP1-001を取得する必要が出てきたのでPass4Testここで購入。勉強しやすくなっていました。