A customer has purchased two dual-port Fibre Channel and two dual-port Ethernet cards. Which configuration will provide the greatest amount of redundancy for two client partitions?
A. Assign all resources to a VIO server. Create an Etherchannel on thenetwork adapters that connect to different FCoE switches.
B. Assign each client one fibre and Ethernet card. Make sure they are cabled to a different network and fibre switches.
C. Assign each client one port on each of the fibre and Ethernet cards. Cable each to a different network or fibre switch.
D. Create a dual VIO server environment, each with one Ethernet and fibre card. Make sure each card is attached to a different network and fibre switch.
正解:D
質問 2:
Whataction does the following command perform for a new AIX hdisk, hdisk1 ?
chdev -I hdisk1 -a pv=yes
A. Clears volume group locks
B. Sets the physical volume identifier
C. Changes the existing pvid on the disk to Yes'
D. Resets the volume group descriptor area
E. Makes the disk available for use
正解:B
質問 3:
How can an administrator rename hdisk2 to cldisk1?
A. chpv-n cldisk1 hdisk2
B. chdev-I hdisk2-aname=cldisk1
C. rendev-I hdisk2 -n cldisk1
D. clcmd-I hdisk2-d cldisk1
正解:C
質問 4:
The cfgmgr command appears to be taking an excessive time to complete. The administrator was able toquit the command and return to the command prompt. The administrator does not have access to the managing HMC and unable to check for any LED codes.
How else can the cause of the observed delay be determined?
A. Re-issue the command with the W flag.
B. Review the latest entry within /var/log/cfgdb.out.
C. Initiate the ledmon command from a separate session, then re-issue cfgmgr.
D. Start the syslog daemon before re-issuing the command.
正解:A
質問 5:
Which action must be completed on the HMC when a partition is in a Recoverystate?
A. Select Recover Partition Data for the managed system.
B. Select Initialize Partition for the LPAR in Recovery state
C. Select Configuration and Rebuild Managed System.
D. Select Configuration and Restore partition data.
正解:A
質問 6:
A VIO client will use NPIV to boot from the SAN and needs to be installed using NIM.
Which two methods canbe used to gather the WWPN information? (Choose two.)
A. Log into the VIO servers and runlscfg -vl fcsX
B. Check the LPAR properties from the HMC GUI
C. Examine the NIM client properties.
D. Utilize the HMC command line tool, lssyscfg
E. Boot the LPAR and runlscfg -vl fcsX
正解:B,C
質問 7:
What speed and duplex attributes should configured on a virtual Ethernet adapter?
A. Default/Default
B. 10000/Full
C. Auto/Auto
D. 1000/Full
正解:B
質問 8:
Where is the file size limit for all users defined?
A. /etc/environment
B. /etc/security/limits
C. /etc/security/environments
D. /etc/security/environ
正解:B
質問 9:
Based on the following output, what must be done if loglv1 name is changed to db2loglv?
A. Run the chfs command to update /exportfs/db01 logging logical volume to db2loglv.
B. Run the logform command to update the log format of db2loglv.
C. Run the chlv command to update dblv01 logging logical volume to db2loglv.
D. Run the chvg command to update volume group default logging logical volume to db2loglv.
正解:C
田中** -
Pass4Test様のC9010-022参考書問題集を利用して、見事合格しました。
問題は多数出題され、問題を解くスピードも速いです。ありがとうございました。