Which two statements are true about the forwarding table? (Choose two.)
A. The forwarding table is stored in compact flash.
B. The forwarding table contains only active routes.
C. The forwarding table lists each source protocol and preference for each destination.
D. The forwarding table is used to process transit packets.
正解:B,D
質問 2:
-- Exhibit -
user@router> show route protocol static
inet.0: 12 destinations, 12 routes (12 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both
192.168.1.128/27 *[Static/5] 00:03:13 > to 10.20.106.10 via fe-0/0/5.106 192.168.1.144/29 *[Static/5] 00:03:13 > to 10.20.14.131 via ge-0/0/0.0 192.168.1.192/27 *[Static/5] 00:03:13 > to 10.18.1.1 via ge-0/0/1.0 192.168.1.128/28 *[Static/5] 00:01:06 > to 10.20.14.130 via ge-0/0/0.0 -- Exhibit -
Given the routing entries shown in the exhibit, which next-hop IP address will be used for the destination IP address 192.168.1.142? (Assume that only static routes are available for the destination.)
A. 10.20.14.130
B. 10.20.14.131
C. 10.18.1.1
D. 10.20.106.10
正解:A
質問 3:
By default, if equal-cost paths exist for the same destination, which action will the router take?
A. Make a copy of the traffic and send it to both destinations.
B. Randomly select one of the available paths to send traffic.
C. Drop half the traffic.
D. Load-balance traffic between the available paths.
正解:B
質問 4:
You accidentally configured interface so-0/0/0.0 with 1.1.1.1/32 instead of 1.1.1.1/30.
Which two solutions could you use to correct this configuration? (Choose two.)
A. [edit interfaces so-0/0/0.0]
user@router# rename family inet address 1.1.1.1/32 to address 1.1.1.1/30
B. [edit interfaces so-0/0/0.0]
user@router# replace family inet address 1.1.1.1/32 with 1.1.1.1/30
C. [edit]
user@router# replace interface so-0/0/0.0 family inet address 1.1.1.1/32 with address 1.1.1.1/30
D. [edit interfaces so-0/0/0.0]
user@router# delete family inet address
user@router# set family inet address 1.1.1.1/30
正解:A,D
質問 5:
When attempting to view the OSPF routes in the routing table, you issue the command show route table inet.3 but no OSPF routes are displayed.
What is the problem?
A. The OSPF routes are located in the inet.0 routing table.
B. The OSPF routes are located in the inet4.3 routing table.
C. The OSPF routes are located in the inet.2 routing table.
D. The OSPF routes are located in the inet4.0 routing table.
正解:A
質問 6:
-- Exhibit -
user@router> show route
inet.0: 9 destinations, 9 routes (9 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both
10.10.10.91/32 *[Direct/0] 00:09:40 > via lo0.0 10.10.10.92/32 *[OSPF/10] 00:01:50, metric 1 > to 172.16.1.2 via ge-0/0/2.0 100.100.1.0/24 *[Static/5] 00:01:50 Reject 172.16.1.0/24 *[Direct/0] 00:06:09 > via ge-0/0/2.0 172.16.1.1/32 *[Local/0] 00:06:09 Local via ge-0/0/2.0 192.168.0.0/16 *[Aggregate/130] 00:00:06 Reject 192.168.0.0/17 *[Aggregate/130] 00:00:06 > to 172.16.1.2 via ge-0/0/2.0 192.168.50.0/24 *[Static/5] 00:00:06 > to 172.16.1.2 via ge-0/0/2.0 192.168.51.0/24 *[Static/5] 00:00:06 > to 172.16.1.2 via ge-0/0/2.0
user@router> show configuration policy-options
policy-statement demo { term 1 { from { protocol aggregate; route-filter 192.168.0.0/16 longer;
}
then accept;
}
}
user@router> show configuration protocols ospf
export demo;
area 0.0.0.0 {
interface ge-0/0/2.0;
}
-- Exhibit --
Given the configuration and routing table shown in the exhibit, which routes will be advertised to OSPF neighbors because of the demo policy?
A. 192.168.0.0/16 and 192.168.0.0/17
B. 192.168.0.0/17, 192.168.50.0/24, and 192.168.51.0/24
C. 192.168.0.0/17 only
D. 192.168.0.0/16 only
正解:C
質問 7:
Which configuration causes RIP-learned routes to be advertised to other RIP neighbors?
A. top edit policy-options policy-statement demo set term 1 from protocol rip set term 1 then accept top set protocols rip group internal export demo
B. set protocol rip no-passive
C. top edit policy-options policy-statement demo set term 1 from active routes set term 1 then accept top set protocols rip group internal export demo
D. set protocols rip advertise in-out
正解:A
質問 8:
Which command will display the contents of the forwarding table?
A. show configuration
B. show forwarding
C. show route forwarding-table
D. show interfaces
正解:D
中村** -
このJN0-101問題集の品質に非常に感謝しています。 JN0-105を購入して再度受験します