715 お客様のコメント
質問 1：
A technician is configuring Open Shortest Path First (OSPF) on a VSP 9000, and is using this formula shown in the exhibit to determine the OSPF Link State Advertisement (LSA) limits.
What does LSA_CNT in the formula represent?
A. the number of adjacencies for each area
B. the number of CNTs for all areas
C. the number of LSAs for all areas
D. the number of LSAs for a given area
正解：D
質問 2：
A technician is enabling SSH-2 in secure mode on a VSP 9000, and also wants to allow SNMP access. Which statement about SNMP access is true?
A. SNMPv1and SNVPv2 areautomatically allowed. Add SNMPv3is allowed manually.
B. Manually change the block SNMP flag to false.
C. Use the SSH-1boot flag setting to allow SNMP access.
D. The system automatically allows SNMP access.
正解：B
質問 3：
Which statement describes a valid guideline for proper operators of Border Gateway Protocol (BGP) on a VSP 9000?
A. For routers that support both BGP and OSPF, the OSPFrouter ID and the BGP identifier must be configured to different IP addresses.
B. Use the max-peer-route parameter to limit the number of routes BGP imports from a peer.
C. Ensure the routers that need DGP to operate are in forwarding mode.
D. If Open Shortest Path First (OSPF) is the Interior GatewayProtocol (IGP), use a new OSPF tagconstruction.
正解：C
質問 4：
The network was scheduled for some additional network configuration in the distribution and core switch clusters. The engineer completed the configuration and tested the additional VLANs, along with IP addressing and dynamic routing. All of the tests passed for the new addition in the core, distribution and the edge. A few days later a service rail was logged with the service center regarding the recently added changes to the network. The clients in the new subnet are unable to connect to the new service. Which tools and techniques should be used to resolve the problem?
A. The firsttest is to examine the Forwarding Data Base (FDB) on all of the switches between the source and destination.
B. The first test is to do a ping test to the source and destination from any station in the network.
C. Review the problem statement, and gatherinformation on wh3t is working and what is notworking.
D. Always review the logs forthe core,distribution and edge devices looking for traps.
正解：D
質問 5：
A technician is working on a VSP 9000 and trying to determine why IST in not coming up, even though it is enabled. The configuration looks good. What should he checked next?
A. the physical layer
B. the Key Health Indicators (KHI) stats
C. the slow SFPs
D. the network loops
正解：A
質問 6：
How does a technician access Flight Recorder functionality?
A. through the traffic surveillance utility
B. User-mode CLI
C. ACLI
D. menu item selection
正解：C
A technician is configuring Open Shortest Path First (OSPF) on a VSP 9000, and is using this formula shown in the exhibit to determine the OSPF Link State Advertisement (LSA) limits.
What does LSA_CNT in the formula represent?
A. the number of adjacencies for each area
B. the number of CNTs for all areas
C. the number of LSAs for all areas
D. the number of LSAs for a given area
正解：D
質問 2：
A technician is enabling SSH-2 in secure mode on a VSP 9000, and also wants to allow SNMP access. Which statement about SNMP access is true?
A. SNMPv1and SNVPv2 areautomatically allowed. Add SNMPv3is allowed manually.
B. Manually change the block SNMP flag to false.
C. Use the SSH-1boot flag setting to allow SNMP access.
D. The system automatically allows SNMP access.
正解：B
質問 3：
Which statement describes a valid guideline for proper operators of Border Gateway Protocol (BGP) on a VSP 9000?
A. For routers that support both BGP and OSPF, the OSPFrouter ID and the BGP identifier must be configured to different IP addresses.
B. Use the max-peer-route parameter to limit the number of routes BGP imports from a peer.
C. Ensure the routers that need DGP to operate are in forwarding mode.
D. If Open Shortest Path First (OSPF) is the Interior GatewayProtocol (IGP), use a new OSPF tagconstruction.
正解：C
質問 4：
The network was scheduled for some additional network configuration in the distribution and core switch clusters. The engineer completed the configuration and tested the additional VLANs, along with IP addressing and dynamic routing. All of the tests passed for the new addition in the core, distribution and the edge. A few days later a service rail was logged with the service center regarding the recently added changes to the network. The clients in the new subnet are unable to connect to the new service. Which tools and techniques should be used to resolve the problem?
A. The firsttest is to examine the Forwarding Data Base (FDB) on all of the switches between the source and destination.
B. The first test is to do a ping test to the source and destination from any station in the network.
C. Review the problem statement, and gatherinformation on wh3t is working and what is notworking.
D. Always review the logs forthe core,distribution and edge devices looking for traps.
正解：D
質問 5：
A technician is working on a VSP 9000 and trying to determine why IST in not coming up, even though it is enabled. The configuration looks good. What should he checked next?
A. the physical layer
B. the Key Health Indicators (KHI) stats
C. the slow SFPs
D. the network loops
正解：A
質問 6：
How does a technician access Flight Recorder functionality?
A. through the traffic surveillance utility
B. User-mode CLI
C. ACLI
D. menu item selection
正解：C
おお** -
3601問題集を勉強して、私は都市の大手なテクノロジー会社に雇われた。品質高い3601問題集に感謝に念に耐えません。